| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
can: bcm: add locking when updating filter and timer values
KCSAN detected a simultaneous access to timer values that can be
overwritten in bcm_rx_setup() when updating timer and filter content
while bcm_rx_handler(), bcm_rx_timeout_handler() or bcm_rx_thr_handler()
run concurrently on incoming CAN traffic.
Protect the timer (ival1/ival2/kt_ival1/kt_ival2/kt_lastmsg) and filter
(nframes/flags/frames/last_frames) updates in bcm_rx_setup() with a new
per-op bcm_rx_update_lock, taken with the matching scope in the RX
handlers. memcpy_from_msg() is staged into a temporary buffer before the
lock is taken, since it can sleep and must not run under a spinlock.
hrtimer_cancel() is always called without bcm_rx_update_lock held, since
bcm_rx_timeout_handler()/bcm_rx_thr_handler() take the same lock and a
running callback would otherwise deadlock against the canceller.
Also close a related race: bcm_rx_setup() cleared the RTR flag in the
stored reply frame's can_id as a separate, unprotected step after the
frame content was already installed, so a concurrent bcm_rx_handler()
could transmit a stale reply with CAN_RTR_FLAG still set. Fold that
normalization into the initial frame preparation instead (on the staged
buffer for updates, directly on op->frames pre-registration for new
ops), so the installed frame is always atomically self-consistent.
bcm_rx_handler()'s RX_RTR_FRAME check now takes a lock-protected
snapshot of op->flags before deciding whether to call bcm_can_tx(),
but does not hold the lock across that call.
Also take a lock-protected snapshot of the currframe in bcm_can_tx()
to avoid partly overwrites by content updates in bcm_tx_setup().
Finally check if a TX_RESET_MULTI_IDX/SETTIMER might have reset
op->currframe between the two locked sections in bcm_can_tx().
Omit calling hrtimer_forward() with zero interval in bcm_rx_thr_handler().
kt_ival2 may have been concurrently cleared by bcm_rx_setup() before it
cancels this timer, so check kt_ival2 inside the bcm_rx_update_lock. |
| In the Linux kernel, the following vulnerability has been resolved:
can: bcm: fix lockless bound/ifindex race and silent RX_SETUP failure
bcm_sendmsg() reads bo->ifindex and checks bo->bound before taking
lock_sock(), while bcm_notify(), bcm_connect() and bcm_release() all
mutate both fields under that same lock. Because the lockless reads
and the locked writes are unordered with respect to each other, a
racing bcm_notify() (device unregister) or bcm_connect() (concurrent
bind on another thread sharing the socket) can make bcm_sendmsg()
observe an inconsistent combination, e.g. a stale bound=1 together
with the now-cleared ifindex=0, silently turning a socket bound to a
specific CAN interface into one that also matches "any" interface.
Keep the lockless bo->bound check purely as a fast-path reject, and
move the ifindex read (and a bo->bound re-check) into the locked
section, where every writer already serializes. This removes the
possibility of observing the two fields torn against each other,
rather than trying to fix it with more READ_ONCE()/WRITE_ONCE() pairs
on two independently updated fields. Annotate the now-purely-lockless
bo->bound accesses consistently across all its write sites.
Also fix bcm_rx_setup() silently returning success when the target
device disappears concurrently instead of reporting -ENODEV, so a
broken RX op is no longer left registered as if it had succeeded. |
| In the Linux kernel, the following vulnerability has been resolved:
can: isotp: serialize TX state transitions under so->rx_lock
The TX state machine (so->tx.state) is driven from three contexts:
sendmsg() claiming and progressing a transfer, the RX path consuming
Flow Control/echo frames, and two hrtimers timing out a stalled
transfer. Mixing a lock-free cmpxchg() claim in sendmsg() with
hrtimer_cancel() calls made under so->rx_lock elsewhere left windows
where a frame or timer callback could act on a state that had already
moved on, corrupting an unrelated transfer.
so->rx_lock now covers the full lifecycle of a TX claim: sendmsg()
takes it to check so->tx.state is ISOTP_IDLE, switch it to
ISOTP_SENDING, bump so->tx_gen and drain the previous transfer's
timers - all as one critical section. isotp_rcv_fc()/isotp_rcv_cf()
already run under this lock via isotp_rcv(), and isotp_rcv_echo() now
takes it itself, so none of them can ever observe a transfer mid-claim.
This also means a transfer can no longer be handed to sendmsg()'s
cleanup paths (signal or send error) while another thread is
concurrently claiming or finishing it, so those paths can cancel
timers and reset the state unconditionally.
isotp_release() claims the socket the same way, so a racing sendmsg()
sees a consistent ISOTP_SHUTDOWN and skips arming its timer or sending.
Only the hrtimer callbacks stay outside so->rx_lock, since they run
under so->rx_lock's cancellation elsewhere and taking it themselves
would deadlock. so->tx_gen lets them recognize whether the transfer
they timed out is still the one currently active, so they don't
report an error against a transfer that has since completed or been
superseded. |
| In the Linux kernel, the following vulnerability has been resolved:
netdev-genl: report NAPI thread PID in the caller's pid namespace
netdev_nl_napi_fill_one() reports the NAPI kthread PID in NETDEV_A_NAPI_PID
using task_pid_nr(), which returns the PID in the initial pid namespace.
NETDEV_CMD_NAPI_GET does not have GENL_ADMIN_PERM and the netdev genl family
is netnsok, so a caller in a child pid namespace can issue it. That caller
then sees the kthread's global PID, even though the kthread is not visible
in its pid namespace, where the value should be 0.
Translate the PID through the caller's pid namespace, the same way commit
3799c2570982 ("io_uring/fdinfo: translate SqThread PID through caller's
pid_ns") did for the io_uring SQPOLL thread. The doit and dumpit paths both
run synchronously in the caller's context, so task_active_pid_ns(current) is
the caller's pid namespace. |
| In the Linux kernel, the following vulnerability has been resolved:
nvmet: fix refcount leak in nvmet_sq_create()
In nvmet_sq_create(), a reference on the ctrl is taken
via kref_get_unless_zero() before calling nvmet_check_sqid().
If nvmet_check_sqid() fails, the function returns the error
directly without releasing the reference, leading to a leak.
Fix this by jumping to the "ctrl_put" label, which already
performs the necessary nvmet_ctrl_put(ctrl). This ensures the
reference is properly released on this error path. |
| In the Linux kernel, the following vulnerability has been resolved:
tracing: Check return value of __register_event() in trace_module_add_events()
trace_module_add_events() ignores the return value of __register_event()
and unconditionally calls __add_event_to_tracers() for each event.
If __register_event() fails (for example, if event_init() fails), the
trace_event_call is not added to ftrace_events list, but
__add_event_to_tracers() still creates a trace_event_file pointing to it.
If module loading subsequently fails and module memory is freed, tracing
state retains a stale trace_event_call pointer in trace_event_file,
leading to a use-after-free when tracefs or tracing subsystem operations
are later executed.
Fix this by checking the return value of __register_event() and only
calling __add_event_to_tracers() if event registration succeeded. |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: reject repeated SMB2 NEGOTIATE requests
Unauthenticated client can send multiple successful SMB2 NEGOTIATE
requests on one connection before SESSION_SETUP. While the connection is
in KSMBD_SESS_NEED_SETUP, smb2_handle_negotiate() accepts another
SMB3.1.1 NEGOTIATE and overwrites conn->preauth_info with a new allocation.
Only the final allocation is freed when the connection is released, leaking
one object for every additional successful request.
A repeated SMB2 NEGOTIATE after a dialect has been selected is a protocol
violation. MS-SMB2 section 3.3.5.4 requires the server to disconnect
without replying in this case. Set the connection exiting when rejecting
the request, in addition to suppressing the response.
Reject SMB2 NEGOTIATE unless the connection is new or is waiting for the
SMB2 NEGOTIATE that follows an SMB1 multi-protocol negotiate. Serialize
both SMB1 and SMB2 negotiation paths under conn->srv_mutex, since they
update connection-wide dialect and negotiation state.
Move the locking contract to ksmbd_smb_negotiate_common(), where the state
and dialect are selected, and add ksmbd_conn_new() for consistent state
access. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: usb-audio: fix stack info leak in RME Digiface status
snd_rme_digiface_read_status() reads a four-word status block from the
device into an uninitialised on-stack __le32 buf[4] and, whenever the
vendor control-IN transfer does not return a negative error, copies all
four words into the caller's status[].
snd_usb_ctl_msg() copies the full requested size back into the caller's
buffer regardless of how many bytes the data stage actually delivered:
buf = kmemdup(data, size, GFP_KERNEL);
err = usb_control_msg(dev, pipe, request, requesttype,
value, index, buf, size, timeout);
memcpy(data, buf, size);
usb_control_msg() returns the transferred length on a short control-IN,
which is a non-negative value, and writes only that many bytes. The
remainder of the copy back is the kmemdup()ed image of the caller's
buffer, so a device answering with a short data stage leaves the
trailing words of buf[] holding leftover kernel stack. The only guard
in the caller is err < 0, so those words are stored into status[].
They then reach user space: snd_rme_digiface_get_status_val() selects a
16-bit halfword of status[] per the control's reg/mask, and the eight
Digiface status controls together expose the whole 16-byte frame to an
unprivileged reader of /dev/snd/controlC*.
Zero-initialise the buffer so a short read yields zeros instead of stack
residue. This mirrors snd_rme_get_status1(), which already clears its
output word before the same kind of vendor read.
Discovered by XBOW, triaged by Baul Lee <baul.lee@xbow.com> |
| In the Linux kernel, the following vulnerability has been resolved:
net: openvswitch: fix skb leak on flow key update failure during ct
ovs_ct_execute() always steals or frees the skb on failure while
ovs_flow_key_update() does not. So, if it fails and we return right
away, the skb ends up leaked.
Fix that by breaking instead and letting the common error handling
code at the bottom of the loop to free the skb properly.
This is a very unlikely scenario as it requires the packet to become
unparseable by applying a set of actions on a previously parseable skb,
but should be fixed nevertheless.
Reported by Sashiko. |
| In the Linux kernel, the following vulnerability has been resolved:
mtd: mchp23k256: use SPI match data for chip caps
The driver stores chip capacity information in both the OF match table
and the SPI id table. Probe currently uses of_device_get_match_data(),
so a non-OF SPI modalias match falls back to mchp23k256_caps even when
the SPI id table selected a different part.
Use spi_get_device_match_data() so SPI id-table driver_data is consumed
when OF match data is absent. This keeps the existing default fallback
while avoiding the wrong MTD geometry for id-table-only matches. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: mac80211: validate extension-frame layout before RX
Extension frames only have the extension header at the regular 802.11
header offset. The generic RX path can still reach helpers and interface
dispatch code that read regular header address fields before unsupported
extension subtypes are dropped.
mac80211 currently only handles S1G beacon extension frames. Drop other
extension subtypes before they can reach regular-header RX processing.
For S1G beacons, linearize the SKB with the management-frame path and
require the fixed S1G beacon header, including optional fixed fields
indicated by frame control, before generic RX dispatch.
Route S1G beacons through the station/default-link RX path without
regular-header station lookup. Avoid regular-header address reads in the
mac80211 RX paths that process S1G extension beacons, including
accept-frame, duplicate-detection, address-copy, and MLO
address-translation paths.
Also make ieee80211_get_bssid() length-safe before returning the S1G
source-address pointer. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ieee80211: validate MLE common info length
ieee80211_mle_common_size() uses the first common-info octet as the
common information length for all known MLE types. However,
ieee80211_mle_size_ok() only validates that octet for Basic, Probe
Request, and TDLS MLEs.
Reconfiguration MLEs also skipped the length octet when calculating the
minimum common size, and Priority Access MLEs skipped validation of the
advertised common information length.
Account for the Reconfiguration common-info length octet and validate
the advertised common information length for all known MLE types. Keep
unknown-type handling unchanged.
[remove now misleading comment] |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: cfg80211: validate EHT MLE before MLD ID read
cfg80211_gen_new_ie() copies ML probe response elements from
the parent frame when the parent EHT multi-link element has an
MLD ID matching the nontransmitted BSSID index.
The code only checked that the extension element had more than
one byte before calling ieee80211_mle_get_mld_id(). That helper
assumes a BASIC MLE with enough common info and documents that
callers must first use ieee80211_mle_type_ok().
Attack chain:
malicious AP sends a short EHT MLE in an MBSSID beacon.
cfg80211_inform_bss_frame_data() stores the copied IE buffer.
cfg80211_parse_mbssid_data() builds the nontransmitted BSS IE.
cfg80211_gen_new_ie() sees the EHT MLE in the parent frame.
ieee80211_mle_get_mld_id() then reads past the IE boundary.
Validate the MLE type and size before reading the MLD ID. This
matches the contract required by the MLE helper and rejects the
short element before any internal MLE fields are accessed. |
| In the Linux kernel, the following vulnerability has been resolved:
powerpc/spufs: fix out-of-bounds access in spufs_mem_mmap_access()
spufs_mem_mmap_access() computes the local store offset as
address - vma->vm_start, but bounds-checks it against vma->vm_end
instead of the local store size. On 64-bit, offset is always well
below vma->vm_end, so the clamp never fires and len stays unbounded
against the LS_SIZE buffer returned by ctx->ops->get_ls().
Reject offsets at or beyond LS_SIZE and clamp len to the remaining
space, mirroring the guard already used by spufs_mem_mmap_fault() and
spufs_ps_fault(). |
| In the Linux kernel, the following vulnerability has been resolved:
tracing/user_events: Fix use-after-free in user_event_mm_dup()
user_event_mm_dup() walks the parent mm's enabler list locklessly under
rcu_read_lock() during fork() (from copy_process()); it does not take
event_mutex:
rcu_read_lock();
list_for_each_entry_rcu(enabler, &old_mm->enablers, mm_enablers_link)
enabler->event = user_event_get(orig->event);
user_event_enabler_destroy() removes an enabler from that list with
list_del_rcu() and then, without waiting for a grace period, drops the
enabler's user_event reference with user_event_put() and frees the enabler
with kfree(). A reader that loaded the enabler before the list_del_rcu()
can still be walking it, which leads to two use-after-frees:
- kfree(enabler) frees the enabler while that reader dereferences
enabler->event.
- user_event_put() may drop the last reference to the user_event, which
is then freed (via delayed_destroy_user_event() on a work queue), while
the same reader does user_event_get(orig->event) on it.
Both are reachable by an unprivileged task that can open user_events_data:
one multithreaded process that registers an enabler and then concurrently
unregisters it and calls fork() triggers the race. KASAN reports a
slab-use-after-free in user_event_mm_dup() during clone(), with a
"refcount_t: addition on 0" warning when the user_event is freed.
The enabler use-after-free was found first; the user_event one was reported
by XIAO WU, and the earlier enabler-only fix did not address it.
Defer both the user_event_put() and the kfree(enabler) to a work item
queued with queue_rcu_work(), so they run only after an RCU grace period,
once all readers walking the enabler list have finished. The put must run
in process context because user_event_put() takes event_mutex on the last
reference, so a work queue is used rather than call_rcu(). The now-unlocked
put lets the locked argument of user_event_enabler_destroy() be removed;
all callers are updated. |
| In the Linux kernel, the following vulnerability has been resolved:
ASoC: codecs: simple-mux: Fix enum control bounds check
simple_mux_control_put() rejects values greater than e->items, but
enum control values are zero based. For the two-entry mux used by this
driver, valid values are 0 and 1, so value 2 must be rejected as well.
Accepting e->items can store an invalid mux state, pass it to the GPIO
setter, and pass it on to the DAPM mux update path where it is used as
an index into the enum text array.
Use the same >= e->items check used by the ASoC enum helpers. |
| In the Linux kernel, the following vulnerability has been resolved:
mac802154: remove interfaces with RCU list deletion
Queue wake, stop, and disable paths walk local->interfaces under RCU.
The bulk hardware teardown path removes entries with list_del(), so an
asynchronous transmit completion can follow a poisoned list node in
ieee802154_wake_queue().
Use list_del_rcu() as in the single-interface removal path. The following
unregister_netdevice() waits for in-flight RCU readers before freeing the
netdevice, so no separate grace-period wait is needed. |
| In the Linux kernel, the following vulnerability has been resolved:
dm era: fix out-of-bounds memory access for non-zero start sector
dm-era tracks writes in target-relative blocks, but era_map() calculates
the writeset block before applying the target offset. Tables with a
non-zero start sector can therefore pass an absolute mapped-device block
to metadata_current_marked().
If the absolute block is beyond the current writeset size,
writeset_marked() tests past the end of the in-core bitset. KASAN reports
this as a vmalloc-out-of-bounds access.
Apply the target offset before calculating the era block so writeset
lookups use the target-relative block number. |
| In the Linux kernel, the following vulnerability has been resolved:
dibs: loopback: validate offset and size in move_data()
The loopback move_data() performs a memcpy into the registered DMB
without checking whether offset + size exceeds the DMB length. Unlike
real ISM hardware, which enforces memory region bounds natively, the
software loopback has no such protection.
A peer-supplied out-of-bounds offset or oversized write would result in
an OOB write past the allocated kernel buffer. Add an explicit bounds
check before the memcpy to reject such requests with -EINVAL. |
| IBM Storage Scale 5.2.3.0 through 5.2.3.8, and 6.0.0.0 through 6.0.1.0 GUI contains a hardcoded token in the source code, which was used for inter-node cluster communication and REST API authentication between GUI. |
