Export limit exceeded: 381902 CVEs match your query. Please refine your search to export 10,000 CVEs or fewer.
Search
Search Results (381902 CVEs found)
| CVE | Vendors | Products | Updated | CVSS v3.1 |
|---|---|---|---|---|
| CVE-2026-74677 | 1 Linux | 1 Linux Kernel | 2026-08-22 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: net: usb: ipheth: fix carrier_work UAF on disconnect ipheth_sndbulk_callback() re-arms the carrier-check work on any non-zero URB status: else schedule_delayed_work(&dev->carrier_work, 0); Nothing ties that to the interface being up, so the work can be armed again after ipheth_close() has already drained it, and stay armed until the netdev whose private area embeds it is freed. On unplug with a TX URB in flight, ipheth_disconnect() drains the work through unregister_netdev() -> ipheth_close() -> cancel_delayed_work_sync() and only then calls ipheth_kill_urbs(). usb_kill_urb() completes the in-flight TX URB with -ENOENT, so ipheth_sndbulk_callback() runs after the drain and re-arms carrier_work. The same completion also re-arms the work if the interface is only brought down while a TX URB is in flight, and ipheth_carrier_check_work() then keeps re-queueing itself once a second. unregister_netdev() does not call ipheth_close() for an already-down interface, so nothing drains it on the later unplug either. In both cases free_netdev() frees the netdev while carrier_work is still pending, and ipheth_carrier_check_work() dereferences freed memory. Tie the work to the interface state instead of chasing the completion: disable it in ipheth_close() and enable it in ipheth_open(), so a schedule_delayed_work() from the URB completion is a no-op whenever the interface is not up. disable_delayed_work_sync() also waits for a running instance, so it fully replaces the cancel_delayed_work_sync() it takes the place of. The work starts out disabled in ipheth_probe() so the enable/disable counts balance from the first open. Reproduced under KASAN on linux-next (next-20260731) with dummy_hcd and raw-gadget standing in for the device, driving the second path above (the interface is already down, so unregister_netdev() does not call ipheth_close()): 15 of 15 unpatched boots report a slab-use-after-free in __run_timers(), freed by ipheth_disconnect() and re-armed from ipheth_sndbulk_callback() via queue_delayed_work_on(). The same trigger on a kernel differing only by this patch reports 0 of 15, and the carrier check still functions across open/close cycles. The reproducer needs an attached USB device that stops draining bulk OUT, plus a link down and unplug, driven as root. It is not a privilege boundary crossing and no exploit primitive was developed. Found by 0sec (https://0sec.ai). | ||||
| CVE-2026-74695 | 1 Linux | 1 Linux Kernel | 2026-08-22 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: netfilter: nf_flow_table: drop existing skb dst before skb_dst_set_noref() Incoming skbs passing through netfilter flowtable offload hooks (or XFRM offload path) might already carry a ref-counted dst_entry assigned during earlier RX or routing steps. Calling skb_dst_set_noref() when skb already holds a ref-counted dst overwrites skb->_skb_refdst, leaking the previous dst_entry reference count and triggering a DEBUG_NET_WARN_ON_ONCE assertion in skb_dst_check_unset(): WARNING: at skb_dst_check_unset include/linux/skbuff.h:1170 WARNING: at skb_dst_set_noref include/linux/skbuff.h:1234 WARNING: at nf_flow_offload_ip_hook+0xf6c/0x2b60 net/netfilter/nf_flow_table_ip.c:864 Drop any existing dst_entry reference with skb_dst_drop(skb) before setting the non-referenced flowtable destination. | ||||
| CVE-2026-74700 | 1 Linux | 1 Linux Kernel | 2026-08-22 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: net/sched: cls_api: Always acquire rtnl_lock when destroying locked classifiers Another challenge with unlocked filters. There is a short window in tc_new_tfilter where a tcf_proto can be found and briefly referenced by a totally unrelated, unlocked classifier's request and cause a race. Feng created a poc which created this race with two threads, one creating a u32 filter and other a flower filter in the same chain/prio: 1. Both threads enter tc_new_tfilter, both find the chain empty, both drop filter_chain_lock 2. u32 finishes tcf_proto_create("u32") first, calls tcf_chain_tp_insert_unique() -> inserts u32_tp into the chain 3. flower finishes tcf_proto_create("flower") later, calls tcf_chain_tp_insert_unique() -> tcf_chain_tp_find() now sees u32_tp already there, takes a reference on it, destroys flower's own tp_new and returns u32_tp to the caller. Flower then hits the kind mismatch check (because it requested for kind "flower" but tp->ops->kind is "u32") and goes through the errout path which calls tcf_proto_put() on u32_tp. If the u32 thread has already gone through its own errout (its change() call failed on the PoC's empty options) and dropped its create and insert refs, flower's put is the last one and drops u32_tp's refcnt to zero. At this point tp->ops->destroy() runs in a context that never took rtnl_lock. When that happens, it might cause a UAF like the following (illustrated by the PoC): [ +0.000710] BUG: KASAN: slab-use-after-free in u32_init (net/sched/cls_u32.c:393) [ +0.000281] Read of size 8 at addr ffff888120022f00 by task poc_feng_xue/524 Call Trace: u32_init (net/sched/cls_u32.c:393) tc_new_tfilter (net/sched/cls_api.c:2378) Allocated by task 526: u32_init (net/sched/cls_u32.c:378) tc_new_tfilter (net/sched/cls_api.c:2378) Freed by task 522: kfree u32_destroy (net/sched/cls_u32.c:662) tcf_proto_destroy (net/sched/cls_api.c:446) tcf_proto_put (net/sched/cls_api.c:459) tc_new_tfilter (net/sched/cls_api.c:2459) Fix this by having tcf_proto_destroy() take rtnl_lock around tp->ops->destroy() for locked classifiers whenever rtnl is not held. To explain why I used a temp variable "not_lockless" I'd like to point to a semi-related note on rtnl_held vs TCF_PROTO_OPS_DOIT_UNLOCKED (adding here for future cleanup if deemed necessary): The rtnl_held parameter and the TCF_PROTO_OPS_DOIT_UNLOCKED flag are redundant sources of truth for whether rtnl_lock is held. Among the nine classifier destroy(..rtnl_held..) callbacks, only flower consults the rtnl_held parameter which it propagates to tc_setup_cb_destroy() and tc_setup_cb_call(). The other eight (u32, flow, bpf, cgroup, route, basic, fw, mall) ignore it entirely;-> those that call tc_setup_cb_destroy() (u32, bpf, mall) hardcode true always instead of forwarding the parameter. A future cleanup should remove the rtnl_held parameter from the destroy callback signature entirely and have callers rely solely on their knowledge whether they are running in an unlocked context. | ||||
| CVE-2026-74709 | 1 Linux | 1 Linux Kernel | 2026-08-22 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: xsk: clear metadata pointer when no timestamp is requested User space can change metadata flags after request processing. Rereading them during completion can therefore make the kernel write a timestamp that was not requested when the packet was submitted. Clear the metadata pointer during request processing unless timestamp completion is requested. Completion handling can then use the pointer itself instead of rereading the flags. On the mlx5 multi-packet WQE path metadata is evaluated per batch: xsk_tx_metadata_request() runs only for the descriptor that starts a session, just like the checksum offload that is applied once through the shared WQE. Only that descriptor's pointer is reset, so completion handling can record a timestamp for the other descriptors of the session regardless of their own XDP_TXMD_FLAGS_TIMESTAMP bit. The write stays inside the metadata area; the single-WQE, other zero-copy, and generic paths reset the pointer per descriptor and are unaffected. | ||||
| CVE-2026-74724 | 1 Linux | 1 Linux Kernel | 2026-08-22 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: ipvs: avoid out-of-bounds write in ip_vs_nat_icmp Sashiko warns that local attacker can modify the packet while it is processed by IPVS. Some places read the IP ihl field multiple times which can cause out-of-bounds access. One such place is ip_vs_nat_icmp where we can write after the validated area. Fix it by providing ciph argument just like it is done for IPv6 and use ciph->len as offset to the embedded transport header. Modify some IPv4 header checks by reading the ihl field only once. | ||||
| CVE-2026-74592 | 1 Linux | 1 Linux Kernel | 2026-08-22 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: ima: Instantiate file_truncate and path_truncate hooks Instantiate the file_truncate and path_truncate LSM hooks to reset the action cache flags (IMA_DONE_MASK) as soon as truncation is requested, so the file, based on policy, is re-collected, re-measured, re-audited, and re-appraised on next access. | ||||
| CVE-2026-74667 | 1 Linux | 1 Linux Kernel | 2026-08-22 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: net/packet: reset the MAC header on the packet-socket transmit path packet_parse_headers() resets the MAC header only for a SOCK_RAW frame whose socket did not bind a protocol. A protocol-bound SOCK_RAW socket, any SOCK_DGRAM frame, and the legacy SOCK_PACKET path therefore leave skb->mac_header unset here. For frames sent via __dev_queue_xmit() this is harmless: it resets the MAC header unconditionally. But the packet-socket PACKET_QDISC_BYPASS path uses dev_direct_xmit(), which does not, so the frame reaches ndo_start_xmit() with the MAC header unset. A driver that reads eth_hdr(skb) on transmit then dereferences skb->head + (u16)~0, an out-of-bounds access ~64 KiB past the head -- the same class fixed for one consumer in commit f5089008f90c ("macsec: do not read an unset MAC header in macsec_encrypt()"). packet_parse_headers() runs only on the transmit path, where skb->data points at the start of the L2 header for every packet-socket type regardless of its length: SOCK_RAW and SOCK_PACKET carry a user-supplied header and SOCK_DGRAM has one built by dev_hard_header(). Reset the MAC header unconditionally, mirroring __dev_queue_xmit(), so the frame is anchored on the bypass path too. Found by 0sec (https://0sec.ai) using automated source analysis; verified against source and matched to the macsec KASAN report in f5089008f90c. Compile-tested. | ||||
| CVE-2026-74669 | 1 Linux | 1 Linux Kernel | 2026-08-22 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: ipvs: clear IPv4 options after rebasing tunnel ICMP errors ip_vs_in_icmp() rebases an skb from the outer ICMP packet to the quoted original request before passing it to icmp_send(). However, IPCB(skb)->opt still describes the outer IPv4 header. A timestamp option in the outer header can therefore leave an offset that points into the quoted transport header after the rebase. __ip_options_echo() treats a byte at that stale location as the option length and copies it into the fixed-size option storage on the __icmp_send() stack, causing a stack out-of-bounds write. Clear the stale option metadata after resetting the network header. Keep the remaining control block fields, including the ingress interface used by the ICMP response path. | ||||
| CVE-2026-74673 | 1 Linux | 1 Linux Kernel | 2026-08-22 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: Input: evdev - fix information leak in evdev_pass_values() In evdev_pass_values(), the input_event structure is allocated on the kernel stack and populated field-by-field. However, it is never fully initialized. On architectures where struct input_event contains explicit or implicit padding (such as the 32-bit __pad field on SPARC64), these padding bytes are left uninitialized. When this event structure is subsequently passed to the client buffer and later copied to userspace, the uninitialized padding bytes leak kernel stack memory, potentially exposing sensitive information. Similar issues exist in __evdev_queue_syn_dropped and __pass_event. Fix this by explicitly zeroing the entire event structure with memset() before populating its fields. This ensures all padding bytes are cleared before the data crosses the security boundary. | ||||
| CVE-2026-74681 | 1 Linux | 1 Linux Kernel | 2026-08-22 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: usb: misc: usbio: check ibuf_len against rxbuf_len in bulk msg ibuf_len is the bulk IN (receive) buffer size, but the EMSGSIZE check in usbio_bulk_msg() compares it against txbuf_len — the bulk OUT endpoint size. Both are taken independently from different endpoints in usbio_probe(), so the check is wrong when they differ. Use rxbuf_len for the IN direction. This matches the buffer that actually holds the response data. | ||||
| CVE-2026-74682 | 1 Linux | 1 Linux Kernel | 2026-08-22 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: ALSA: usb-audio: fix OOB write on Type II inbound URBs data_ep_set_params() sizes each URB transfer buffer before it adds the Format Type II transfer delimiter: u->packets = urb_packs; u->buffer_size = maxsize * u->packets; if (fmt->fmt_type == UAC_FORMAT_TYPE_II) u->packets++; /* for transfer delimiter */ u->urb = usb_alloc_urb(u->packets, GFP_KERNEL); buffer_size is computed from the pre-increment packet count and never recomputed, so for a Type II endpoint the buffer is one packet short of the packet count the URB is built with. prepare_inbound_urb() then lays out one iso frame per packet and never consults buffer_size: offs = 0; for (i = 0; i < urb_ctx->packets; i++) { urb->iso_frame_desc[i].offset = offs; urb->iso_frame_desc[i].length = ep->curpacksize; offs += ep->curpacksize; } urb->transfer_buffer_length = offs; urb->number_of_packets = urb_ctx->packets; The last descriptor therefore points one packet past the end of the transfer buffer, where the host controller writes device data on every inbound transfer. prepare_silent_urb() and prepare_playback_urb() bound their fill loops by ctx->buffer_size, so only capture is affected. fmt_type comes from the device's audio streaming descriptors, so any device advertising a Type II capture format hits this once userspace sets hw_params on the stream. KASAN on 7.2.0-rc5 (arm64) with a dummy_hcd/raw-gadget device, one report per inbound transfer: BUG: KASAN: slab-out-of-bounds in dummy_timer Write of size 64 at addr ffff0000186171c0 by task cons02/166 __asan_memcpy dummy_timer hrtimer_run_softirq Allocated by task 166: usb_alloc_coherent snd_usb_endpoint_set_params The buggy address is located 0 bytes to the right of allocated 64-byte region [ffff000018617180, ffff0000186171c0) Compute buffer_size after the delimiter packet has been accounted for, and bound the fill loop by buffer_size, as prepare_silent_urb() already does on the outbound side. This grows every Type II URB allocation by one maxsize packet. Discovered by XBOW, triaged by Baul Lee <baul.lee@xbow.com> | ||||
| CVE-2026-74687 | 1 Linux | 1 Linux Kernel | 2026-08-22 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: watchdog: at91sam9_wdt: prevent timer rearm during teardown at91_ping() rearms the watchdog timer from its callback. timer_delete() neither waits for a running callback nor prevents it from rearming the timer, so probe failure or driver removal can leave the timer accessing the devm-allocated at91wdt after it has been freed. Use timer_shutdown_sync() on both teardown paths. It waits for a running callback and rejects any attempt by the callback to rearm the timer. | ||||
| CVE-2026-74688 | 1 Linux | 1 Linux Kernel | 2026-08-22 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: sctp: clear control chunk transport if it is being removed sctp_make_heartbeat_ack() caches the destination transport in chunk->transport without taking a reference. When src_out_of_asoc_ok is enabled, the HEARTBEAT ACK may remain queued on control_chunk_list instead of being transmitted immediately. If the peer transport is removed while the chunk is still queued, sctp_assoc_rm_peer() drops the transport and schedules it for RCU freeing, but only clears cached transport pointers in out_chunk_list. The queued control chunk therefore retains a dangling transport pointer. Once an ASCONF_ACK clears the suppression and the queued control chunk is transmitted, SCTP dereferences the stale transport pointer, leading to a use-after-free. Fix this by also clearing chunk->transport for queued control chunks in control_chunk_list when removing the transport. | ||||
| CVE-2026-74701 | 1 Linux | 1 Linux Kernel | 2026-08-22 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: net/openvswitch: check Ethernet header length in key_extract() When a packet arrives on an ARPHRD_NONE device (e.g. TUN), ovs_flow_key_extract() trusts the user-provided skb->protocol field: if it is ETH_P_TEB, the packet is classified as MAC_PROTO_ETHERNET and key_extract() is called without ensuring the skb has ETH_HLEN (14) bytes of linear data. key_extract() unconditionally pulls 2 * ETH_ALEN bytes for MAC addresses and parse_ethertype() pulls 2 more, either of which triggers a kernel BUG in __skb_pull() when the linear area is too small. kernel BUG at include/linux/skbuff.h:2848! RIP: 0010:key_extract+0xa7e/0xd90 net/openvswitch/flow.c:933 ovs_flow_key_extract+0x419/0xa70 ovs_vport_receive+0x222/0x390 netdev_frame_hook+0x3e0/0x630 tun_get_user+0x2d0c/0x38e0 Fixed by calling check_header() in key_extract() before accessing the Ethernet header. | ||||
| CVE-2026-74705 | 1 Linux | 1 Linux Kernel | 2026-08-22 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: udp: fix potential use-after-free in tunnel segmentation __skb_udp_tunnel_segment() gets the UDP header before ensuring the tunnel header is in the skb head. If the pull reallocates skb->head, the saved UDP header pointer is no longer valid. Get the UDP header after the pull to avoid a potential use-after-free. | ||||
| CVE-2026-74712 | 1 Linux | 1 Linux Kernel | 2026-08-22 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: vdpa/mlx5: Fix buffer length in create_direct_keys() We have seen in our CI the following KASAN message: BUG: KASAN: slab-out-of-bounds in cmd_exec+0x550/0xca0 [mlx5_core] Read of size 272 at addr 0000000176795020 by task qemu-system-s39/82764 [...] [<000011388ab3a7a0>] cmd_exec+0x550/0xca0 [mlx5_core] [<000011388ab3b61c>] mlx5_cmd_exec_cb+0x25c/0x4f0 [mlx5_core] [<000011388b21e82e>] mlx5_vdpa_exec_async_cmds+0x22e/0x5e0 [mlx5_vdpa] [<000011388b21fd44>] create_direct_keys+0x954/0xef0 [mlx5_vdpa] [...] The buggy address is located 4128 bytes inside of allocated 4384-byte region [0000000176794000, 0000000176795120) So in essence we read 16 bytes beyond 4384-byte allocation. create_direct_keys calculates the pointer and length for in and out buffers. The size calculation for in includes the entire structure size (out + in + mtt[]) but the pointer passed to cmd_exec points only to the 'in' field, skipping the 'out' field. This causes mlx5_copy_to_msg() to read beyond the allocated buffer by sizeof(out) bytes when copying command data. Properly calculate the input size to match the pointer and allocation size. | ||||
| CVE-2026-74721 | 1 Linux | 1 Linux Kernel | 2026-08-22 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: accel/amxdna: Fix page-insertion errors in amdxdna_insert_pages() Two error paths in amdxdna_insert_pages() called vma->vm_ops->close(vma) before returning an error code to the caller. This is incorrect: amdxdna_gem_obj_mmap() registers an HMM interval notifier before calling amdxdna_insert_pages(), and on a hard error it jumps to hmm_unreg to undo that registration. Calling vm_ops->close() manually — which drops the shmem pages_pin_count and the GEM object reference that backs the VMA — before the mmap syscall has even returned causes those resources to be released while the VMA is still alive. The kernel VMA teardown will call vm_ops->close() a second time when the process later unmaps the range, producing a reference count underflow. Replace both hard-error returns with a deferred-fault approach that keeps the VMA alive and retries page insertion through the HMM range-fault path. | ||||
| CVE-2026-74723 | 1 Linux | 1 Linux Kernel | 2026-08-22 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: btrfs: lzo: reject inline extents without valid headers [BUG] For a crafted btrfs image, the following KASAN can be triggered when reading an inline lzo compressed file extent: BUG: KASAN: slab-out-of-bounds in lzo_decompress+0x57d/0x700 Read of size 4 at addr ffff888006f2e644 by task btrfs_lzo_inlin/77 Call Trace: <TASK> dump_stack_lvl+0x5b/0x70 print_report+0xd1/0x610 kasan_report+0xe0/0x110 __asan_report_load_n_noabort+0x13/0x20 lzo_decompress+0x57d/0x700 btrfs_decompress+0x140/0x1c0 uncompress_inline+0x147/0x1b0 btrfs_get_extent+0xb23/0x10a0 btrfs_do_readpage.constprop.0+0x538/0x1ac0 btrfs_readahead+0x32f/0x5f0 read_pages+0x16f/0x850 page_cache_ra_unbounded+0x296/0x490 do_page_cache_ra+0xd9/0x130 page_cache_sync_ra+0x3ee/0x6f0 filemap_get_pages+0x306/0x15c0 filemap_read+0x329/0xd00 btrfs_file_read_iter+0x1f8/0x2b0 vfs_read+0x4ef/0x720 ksys_read+0xf8/0x1d0 __x64_sys_read+0x71/0xb0 x64_sys_call+0x1ab0/0x1b70 do_syscall_64+0x61/0x470 entry_SYSCALL_64_after_hwframe+0x4b/0x53 </TASK> [CAUSE] For an inline lzo compressed file extent, there should always be one lzo header, recording the total length of the compressed data, followed by one segment header, recording the compressed lzo payload. But if a crafted inline lzo compressed file extent contains only an lzo header, without the segment header or payload, lzo_decompress() will still try to read the segment header, causing a read beyond the item boundary. Furthermore if the inline lzo compressed file extent is the first item of the leaf, it will be at the extent buffer boundary. The above out-of-boundary read will go beyond the extent buffer boundary, triggering the above KASAN report. [FIX] Validate the total length of the inlined lzo compressed file extent, to make sure there is at least one LZO header and one segment header, and a non-zero payload. [ Rework the commit message to remove slop ] | ||||
| CVE-2026-74728 | 1 Linux | 1 Linux Kernel | 2026-08-22 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: xfs: handle NULL b_addr in xfs_buf_free When xfs_buf_alloc_backing_mem() fails, xfs_buf_free() is called with bp->b_addr still NULL. The code falls through to the folio_put path which calls virt_to_folio(NULL), dereferencing an invalid address and causing a kernel crash. Call Trace: xfs_buf_free+0x25f/0x510 xfs_buf_alloc+0xc98/0x19b0 xfs_buf_find_insert+0x55/0x14d0 xfs_buf_get_map+0x122b/0x17c0 xfbtree_init_leaf_block+0x11c/0x4a0 xfbtree_init+0x1bb/0x460 xrep_rmap_setup_scan+0x100/0x1f0 xrep_rmapbt+0x41/0xc0 Fix this by skipping folio_put() when bp->b_addr is NULL. | ||||
| CVE-2026-74639 | 1 Linux | 2 Kernel, Linux Kernel | 2026-08-22 | N/A |
| In the Linux kernel, the following vulnerability has been resolved: ALSA: us144mkii: re-anchor capture URBs on resubmission capture_urb_complete() resubmits each capture URB without anchoring it: usb_get_urb(urb); ret = usb_submit_urb(urb, GFP_ATOMIC); Anchoring is a property of a submission, not of the URB. The giveback path calls usb_unanchor_urb() before urb->complete(), so an URB resubmitted from its own completion handler is off the anchor. The capture URBs are anchored once, at stream start, so from the first completion onward tascam->capture_anchor is empty. tascam_free_urbs(), tascam_disconnect(), tascam_suspend() and the stop-work path all call usb_kill_anchored_urbs(&tascam->capture_anchor) to reap the capture URBs before anything is freed. With the anchor empty those calls return immediately and the URBs stay queued on the host controller. tascam_free_urbs() then returns the capture transfer buffers with usb_free_coherent(), and snd_card_free() releases the snd_card allocation that embeds tascam (card->private_data). The controller completes the queued URBs afterwards, writing device-supplied data into the freed transfer buffer, and capture_urb_complete() dereferences the freed driver object. KASAN on 7.2.0-rc5 (arm64): BUG: KASAN: slab-use-after-free in dummy_timer Write of size 512 at addr ffff000015b62000 __asan_memcpy dummy_timer hrtimer_run_softirq Allocated by task 64: usb_alloc_coherent tascam_alloc_urbs tascam_probe Freed by task 170: usb_free_coherent tascam_free_urbs tascam_disconnect usb_unbind_interface BUG: KASAN: slab-use-after-free in capture_urb_complete Read of size 4 at addr ffff0000170ee878 Freed by task 170: release_card_device snd_card_free tascam_disconnect Restore the usb_anchor_urb() between the reference count bump and the resubmission. That also makes the handler's usb_unanchor_urb() failure arm meaningful again and restores usb_kill_anchored_urbs() as a barrier on the disconnect, suspend and stop-work paths. The anchoring was removed on the premise that the URB is already anchored from the initial submission, which does not hold once the first giveback has run. Discovered by XBOW, triaged by Baul Lee <baul.lee@xbow.com> | ||||