| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
drm/panthor: validate firmware interface structure sizes
iface_fw_to_cpu_addr() only checks that the firmware-provided MCU virtual
address points inside the shared section. The returned pointer is later
used as a full firmware interface structure, so accepting an address near
the end of the shared section can still lead to out-of-bounds accesses.
Pass the expected object size to iface_fw_to_cpu_addr() and reject ranges
that do not fit entirely in the shared section. |
| In the Linux kernel, the following vulnerability has been resolved:
ntfs: harden runlist realloc size calculations
Add a shared helper to safely convert runlist element counts to byte sizes
using overflow checks, and use it in both ntfs_rl_realloc() and
ntfs_rl_realloc_nofail(). |
| In the Linux kernel, the following vulnerability has been resolved:
iommu/arm-smmu-v3-iommufd: Require exactly one Stream ID for a vDEVICE
arm_vsmmu_vsid_to_sid() maps a guest's vSID to a single physical Stream ID
taken from master->streams[0], assuming a device has exactly one stream. A
device with several streams gets only its first one mapped, so a guest vSID
invalidation cannot reach the others' ATC and IOTLB entries; a device with
none makes master->streams a ZERO_SIZE_PTR, read out of bounds.
Add an arm_vsmmu_vdevice_init() op to reject the vDEVICE with -EOPNOTSUPP
when master->num_streams is not one, rather than mapping it silently. |
| In the Linux kernel, the following vulnerability has been resolved:
ASoC: amd: acp-sdw-sof: Bound DAI link iteration
create_sdw_dailinks() walks sof_dais until it finds an entry with
initialised cleared, but sof_dais is allocated with exactly num_ends
entries. If all entries are initialised, the loop reads past the end of
the array.
Pass the allocated entry count to create_sdw_dailinks() and stop before
reading past the array. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: wcn36xx: fix OOB read from firmware count in PRINT_REG_INFO indication
The firmware-controlled rsp->count field is used as the loop bound for
indexing into the flexible rsp->regs[] array without validation against
the message length. A count exceeding the actual data causes out-of-
bounds reads from the heap-allocated message buffer.
Add a check that count fits within the received message. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: Clear rb node linkage when freeing bpf_rb_root
bpf_rb_root_free() detaches the root by copying the current rb_root_cached
and then replacing the live root with RB_ROOT_CACHED. It then walks the
copied root and drops each object contained in the tree.
This leaves the rb node state intact while dropping the object. If the
object is refcounted and survives the drop, its bpf_rb_node_kern still
contains an owner pointer to the freed root and stale rb tree linkage. If
a later bpf_rb_root allocation reuses the same address, bpf_rbtree_remove()
can incorrectly pass the owner check and call rb_erase_cached() on a node
whose rb pointers belong to the old tree.
Mirror the list draining behavior by marking nodes as busy while the root
is being detached, then clear the rb node and release the owner before
dropping the containing object. This makes surviving nodes unowned and
safe to reject from remove or accept for a later add. |
| In the Linux kernel, the following vulnerability has been resolved:
netfilter: nat: use kfree_rcu to release ops
Florian Westphal says:
"Historically this is not an issue, even for normal base hooks: the data
path doesn't use the original nf_hook_ops that are used to register the
callbacks.
However, in v5.14 I added the ability to dump the active netfilter
hooks from userspace.
This code will peek back into the nf_hook_ops that are available
at the tail of the pointer-array blob used by the datapath.
The nat hooks are special, because they are called indirectly from
the central nat dispatcher hook. They are currently invisible to
the nfnl hook dump subsystem though.
But once that changes the nat ops structures have to be deferred too."
Update nf_nat_register_fn() to deal with partial exposition of the hooks
from error path which can be also an issue for nfnetlink_hook. |
| In the Linux kernel, the following vulnerability has been resolved:
rxrpc: Fix potential UAF after skb_unshare() failure
If skb_unshare() fails to unshare a packet due to allocation failure in
rxrpc_input_packet(), the skb pointer in the parent (rxrpc_io_thread())
will be NULL'd out. This will likely cause the call to
trace_rxrpc_rx_done() to oops.
Fix this by moving the unsharing down to where rxrpc_input_call_event()
calls rxrpc_input_call_packet(). There are a number of places prior to
that where we ignore DATA packets for a variety of reasons (such as the
call already being complete) for which an unshare is then avoided.
And with that, rxrpc_input_packet() doesn't need to take a pointer to the
pointer to the packet, so change that to just a pointer. |
| In the Linux kernel, the following vulnerability has been resolved:
gfs2: Fix use-after-free in iomap inline data write path
The inline data buffer head (dibh) is being released prematurely in
gfs2_iomap_begin() via release_metapath() while iomap->inline_data
still points to dibh->b_data. This causes a use-after-free when
iomap_write_end_inline() later attempts to write to the inline data
area.
The bug sequence:
1. gfs2_iomap_begin() calls gfs2_meta_inode_buffer() to read inode
metadata into dibh
2. Sets iomap->inline_data = dibh->b_data + sizeof(struct gfs2_dinode)
3. Calls release_metapath() which calls brelse(dibh), dropping refcount
to 0
4. kswapd reclaims the page (~39ms later in the syzbot report)
5. iomap_write_end_inline() tries to memcpy() to iomap->inline_data
6. KASAN detects use-after-free write to freed memory
Fix by storing dibh in iomap->private and incrementing its refcount
with get_bh() in gfs2_iomap_begin(). The buffer is then properly
released in gfs2_iomap_end() after the inline write completes,
ensuring the page stays alive for the entire iomap operation.
Note: A C reproducer is not available for this issue. The fix is based
on analysis of the KASAN report and code review showing the buffer head
is freed before use.
[agruenba: Take buffer head reference in gfs2_iomap_begin() to avoid
leaks in gfs2_iomap_get() and gfs2_iomap_alloc().] |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amd/display: Do not skip unrelated mode changes in DSC validation
Starting with commit 17ce8a6907f7 ("drm/amd/display: Add dsc pre-validation in
atomic check"), amdgpu resets the CRTC state mode_changed flag to false when
recomputing the DSC configuration results in no timing change for a particular
stream.
However, this is incorrect in scenarios where a change in MST/DSC configuration
happens in the same KMS commit as another (unrelated) mode change. For example,
the integrated panel of a laptop may be configured differently (e.g., HDR
enabled/disabled) depending on whether external screens are attached. In this
case, plugging in external DP-MST screens may result in the mode_changed flag
being dropped incorrectly for the integrated panel if its DSC configuration
did not change during precomputation in pre_validate_dsc().
At this point, however, dm_update_crtc_state() has already created new streams
for CRTCs with DSC-independent mode changes. In turn,
amdgpu_dm_commit_streams() will never release the old stream, resulting in a
memory leak. amdgpu_dm_atomic_commit_tail() will never acquire a reference to
the new stream either, which manifests as a use-after-free when the stream gets
disabled later on:
BUG: KASAN: use-after-free in dc_stream_release+0x25/0x90 [amdgpu]
Write of size 4 at addr ffff88813d836524 by task kworker/9:9/29977
Workqueue: events drm_mode_rmfb_work_fn
Call Trace:
<TASK>
dump_stack_lvl+0x6e/0xa0
print_address_description.constprop.0+0x88/0x320
? dc_stream_release+0x25/0x90 [amdgpu]
print_report+0xfc/0x1ff
? srso_alias_return_thunk+0x5/0xfbef5
? __virt_addr_valid+0x225/0x4e0
? dc_stream_release+0x25/0x90 [amdgpu]
kasan_report+0xe1/0x180
? dc_stream_release+0x25/0x90 [amdgpu]
kasan_check_range+0x125/0x200
dc_stream_release+0x25/0x90 [amdgpu]
dc_state_destruct+0x14d/0x5c0 [amdgpu]
dc_state_release.part.0+0x4e/0x130 [amdgpu]
dm_atomic_destroy_state+0x3f/0x70 [amdgpu]
drm_atomic_state_default_clear+0x8ee/0xf30
? drm_mode_object_put.part.0+0xb1/0x130
__drm_atomic_state_free+0x15c/0x2d0
atomic_remove_fb+0x67e/0x980
Since there is no reliable way of figuring out whether a CRTC has unrelated
mode changes pending at the time of DSC validation, remember the value of the
mode_changed flag from before the point where a CRTC was marked as potentially
affected by a change in DSC configuration. Reset the mode_changed flag to this
earlier value instead in pre_validate_dsc().
(cherry picked from commit cc7c7121ae082b7b82891baa7280f1ff2608f22b) |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: seq: oss: Fix UAF at handling events with embedded SysEx data
The OSS sequencer processes the input MIDI bytes into a sequencer
event to be dispatched later (in snd_seq_oss_midi_putc() called from
snd_seq_oss_process_event()). When it's a SysEx data, the event
record contains data.ext.ptr pointer to the original SysEx bytes, and
the referred data is copied into the pool afterwards at dispatching.
The problem is that, if the sequencer port gets closed concurrently
before the dispatch, the OSS sequencer core also releases the
resources (in snd_seq_oss_midi_check_exit_port()), while the pending
event may hold a stale pointer, eventually leading to a UAF at a later
dispatch.
Fortunately, there is already a refcounting mechanism (snd_use_lock_t)
for the OSS MIDI device access, and for addressing the issue above, we
just need to extend the refcount until the event gets dispatched.
This patch extends snd_seq_oss_process_event() to give back the
refcount object, which is in turn released after calling the sequencer
dispatcher with the given event in the caller side.
According to the original report, KASAN report as below:
KASAN slab-use-after-free in snd_seq_event_dup+0x40c/0x470
RIP: 0033:0x7f2cb66a6340
Read of size 6
Call trace:
dump_stack_lvl+0x73/0xb0 (?:?)
print_report+0xd1/0x650 (?:?)
srso_alias_return_thunk+0x5/0xfbef5 (?:?)
__virt_addr_valid+0x1a7/0x340 (?:?)
kasan_complete_mode_report_info+0x64/0x200 (?:?)
kasan_report+0xf7/0x130 (?:?)
snd_seq_event_dup+0x40c/0x470 (?:?)
kasan_check_range+0x10c/0x1c0 (?:?)
__asan_memcpy+0x27/0x70 (?:?)
snd_seq_event_dup+0x9/0x470 (?:?)
snd_seq_client_enqueue_event+0x139/0x240 (?:?)
_raw_spin_unlock_irqrestore+0x4b/0x60 (?:?)
snd_seq_kernel_client_enqueue+0x102/0x120 (?:?)
snd_seq_oss_write+0x416/0x4e0 (?:?)
apparmor_file_permission+0x20/0x30 (?:?)
odev_write+0x3b/0x60 (?:?)
vfs_write+0x1ce/0x850 (?:?)
lock_release+0xc8/0x2a0 (?:?)
__kasan_check_write+0x18/0x20 (?:?)
__mutex_unlock_slowpath+0x129/0x510 (?:?)
ksys_write+0xe1/0x180 (?:?)
mutex_unlock+0x16/0x20 (?:?)
odev_ioctl+0x65/0xc0 (?:?)
__x64_sys_write+0x46/0x60 (?:?)
x64_sys_call+0x7d/0x20d0 (?:?)
do_syscall_64+0xc1/0x360 (arch/x86/entry/syscall_64.c:87)
entry_SYSCALL_64_after_hwframe+0x77/0x7f (?:?) |
| In the Linux kernel, the following vulnerability has been resolved:
crypto: ccp - Fix snp_filter_reserved_mem_regions() off-by-one
Sashiko notes:
> regarding the bounds check in snp_filter_reserved_mem_regions()
> called via walk_iomem_res_desc(): does the check
> if ((range_list->num_elements * 16 + 8) > PAGE_SIZE)
> allow an off-by-one heap buffer overflow?
>
> If range_list->num_elements is 255, 255 * 16 + 8 = 4088, which is <= 4096.
> Writing range->base (8 bytes) fills 4088-4095, but writing range->page_count
> (4 bytes) would write to 4096-4099, overflowing the kzalloc-allocated
> PAGE_SIZE buffer.
Fix this by accounting for the entry about to be written to, in addition to
the entries that are already allocated. |
| In the Linux kernel, the following vulnerability has been resolved:
octeontx2-af: Block VFs from clobbering special CGX PKIND state
PF and VF NIX LFs that share a CGX LMAC reuse the same hardware PKIND
programming. When HiGig2 or EDSA parsing is enabled, a VF NIX LF alloc must
not reset the LMAC RX PKIND or default TX parse config over the PF setup.
Add cgx_get_pkind() and rvu_cgx_is_pkind_config_permitted() so VFs skip
cgx_set_pkind(), rvu_npc_set_pkind(), and NIX_AF_LFX_TX_PARSE_CFG updates
when the LMAC is using NPC_RX_HIGIG_PKIND or NPC_RX_EDSA_PKIND. |
| In the Linux kernel, the following vulnerability has been resolved:
vxlan: use pskb_network_may_pull() for transmit path header pulls
In vxlan_xmit(), arp_reduce(), and vxlan_mdb_entry_skb_get(), pskb_may_pull() was
being called to verify the availability of network layer headers (ARP, IPv6/ND,
IP/IPv6 MDB keys).
However, during transmit skb->data points to the MAC header, so skb_network_offset(skb)
is ETH_HLEN (14 bytes). Using pskb_may_pull(skb, len) only checks len bytes from skb->data
rather than skb_network_offset(skb) + len, which can leave part of the network header
in non-linear frags.
Replace these remaining pskb_may_pull() calls with pskb_network_may_pull() to properly
account for the MAC header offset. |
| In the Linux kernel, the following vulnerability has been resolved:
net: pktgen: fix proc entry use-after-free
pktgen_change_name() replaces pkt_dev->entry while holding t->if_lock.
pktgen_remove_device() removes the same entry before
_rem_dev_from_if_list() takes that lock.
This allows the following interleaving:
CPU 0 (NETDEV_CHANGENAME) CPU 1 (kpktgend)
if_lock(t)
proc_remove(pkt_dev->entry)
proc_remove(pkt_dev->entry)
pkt_dev->entry = proc_create_data(...)
if_unlock(t)
The kthread can pass the stale proc_dir_entry to proc_remove() after the
rename path has freed it. A reproducer with a widened race window reports:
BUG: KASAN: slab-use-after-free in proc_remove+0x78/0x80
Read of size 8 at addr ffff8881478fea70 by task kpktgend_0/67
Call Trace:
proc_remove+0x78/0x80
pktgen_remove_device.isra.0+0x11c/0x4c0
pktgen_thread_worker+0x1214/0x6bc0
kthread+0x2c6/0x3b0
Allocated by task 95:
__proc_create+0x204/0x790
proc_create_data+0x72/0xe0
pktgen_thread_write+0xd61/0x1510
Freed by task 28:
kmem_cache_free+0xcb/0x3d0
proc_free_inode+0x5b/0x80
rcu_core+0x50a/0x1850
The buggy address belongs to the object at ffff8881478fea00
which belongs to the cache proc_dir_entry of size 192
Move proc_remove() into the if_lock-protected list removal helper. Keep it
before list_del_rcu() to preserve the ordering required by add_device().
The rename path must then finish replacing the entry before removal, or
it observes that the device is no longer on the list. |
| In the Linux kernel, the following vulnerability has been resolved:
veth: convert frag_list skbs before running XDP
A frag_list skb can reach veth with data_len set but nr_frags zero.
veth_convert_skb_to_xdp_buff() only converts skbs that are shared,
locked, have frags[], or do not have enough headroom. It later uses
skb_is_nonlinear() to decide whether to set XDP_FLAGS_HAS_FRAGS and
xdp_frags_size.
That exposes frag_list data to XDP as if it were stored in frags[], but
frags[] is empty. AF_XDP copy mode can then trust the bogus XDP fragment
metadata, walk an empty fragment entry, and crash in memcpy() from
__xsk_rcv().
Route non-linear skbs through skb_pp_cow_data() before exposing them to
XDP, and only advertise XDP frags when the resulting skb has frags[].
skb_copy_bits() already handles frag_list input, and skb_pp_cow_data()
builds frags[] output with skb_add_rx_frag(), which is the
representation XDP multi-buffer expects. |
| In the Linux kernel, the following vulnerability has been resolved:
rxrpc: Fix the reception of a reply packet before data transmission
Fix rxrpc_receiving_reply() to handle the reception of an apparent reply
DATA packet before rxrpc has had a chance to send any request DATA packets
on a client call by checking to see if the call has been exposed yet by
sending the first packet.
Without this, rxrpc_rotate_tx_window() might oops.
Also fix rxrpc_rotate_tx_window() to handle the Tx queue being empty by
changing the do...while loop into a while loop, just in case a call is
abnormally terminated by an early reply before the last request packet is
transmitted. |
| In the Linux kernel, the following vulnerability has been resolved:
rxrpc: Fix ACKALL packet handling
rxrpc_input_ackall() accepts ACKALL packets without checking whether the
call is in a state that can legitimately have outstanding transmit buffers.
A forged ACKALL can therefore reach a new service call in
RXRPC_CALL_SERVER_RECV_REQUEST before any reply packets have been queued.
In that state call->tx_top is zero and call->tx_queue is NULL, so
rxrpc_rotate_tx_window() dereferences a NULL txqueue and triggers a
null-pointer dereference.
Fix the handling of ACKALL packets by the following means:
(1) Add two new call states: RXRPC_CALL_CLIENT_PRE_SEND which indicates
that the client call is connected, but nothing has been transmitted as
yet; and RXRPC_CALL_CLIENT_AWAIT_ACK, which indicates that everything
has been transmitted at least once, but we're now waiting for the
stuff remaining in the Tx buffer to be ACK'd (retransmissions may
still happen).
The RXRPC_CALL_CLIENT_PRE_SEND state is set when the call is assigned
a channel and transitions to RXRPC_CALL_CLIENT_SEND_REQUEST when the
first packet is transmitted.
RXRPC_CALL_CLIENT_AWAIT_REPLY is then narrowed in scope to indicate
that all Tx packets have been ACK'd and we're now waiting for the
reply to be received.
(2) As per Wyatt Feng's original patch[1], the ACKALL handler then checks
that the call state is one in which there might be stuff in the Tx
buffer to ACK, but now this includes AWAIT_ACK rather than
AWAIT_REPLY. ACKALL packets are ignored if received in the wrong
state.
Note that unlike Wyatt Feng's patch, it's no longer necessary to check
to see if the Tx buffer exists as this the state set now covers this.
(3) Make the ACKALL handler use call->tx_transmitted rather than
call->tx_top as the former is explicitly the highest packet seq number
transmitted, whereas the latter has a looser definition.
Thanks to Jeffrey Altman for a description of the history of the ACKALL
packet[1]. |
| Inconsistent interpretation of http requests ('http request/response smuggling') in .NET allows an unauthorized attacker to bypass a security feature over a network. |
| Unchecked input for loop condition in .NET allows an unauthorized attacker to deny service over a network. |
