| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: core: wake eh reliably when using scsi_schedule_eh
Drivers which use the scsi_schedule_eh function to run the error handler
currently risk the error handler thread never waking once all commands are
timed out or inactive. There is no enforced memory order between setting
the host into error recovery state and counting busy commands. This can
result in a race with scsi_dec_host_busy where neither CPU sees both
conditions of all commands inactive and the host error state to request
waking the error handler.
To fix this, run the scsi_schedule_eh's scsi_eh_wakeup from a new work item
which will use rcu to ensure scsi_schedule_eh's call to scsi_host_busy will
occur after the error state is globally visible and will be seen by any
current scsi_dec_host_busy callers. |
| In the Linux kernel, the following vulnerability has been resolved:
bnxt_en: Handle partially initialized auxiliary devices
bnxt_aux_devices_init() calls auxiliary_device_init() before all fields
used by bnxt_aux_dev_release() are initialized. After
auxiliary_device_init() succeeds, later errors must unwind with
auxiliary_device_uninit(), which invokes the release callback.
The release callback assumes that aux_priv->id, aux_priv->edev,
edev->net and edev->ulp_tbl are all populated. If allocation fails
after auxiliary_device_init(), the release path can otherwise dereference
or clear partially initialized state.
Allocate and attach the bnxt_en_dev and ULP table before calling
auxiliary_device_init(), so the release callback only sees a fully
initialized auxiliary private object. If auxiliary_device_init() itself
fails, free those allocations directly because device_initialize() has not
run and the release callback will not be invoked.
This issue was found by a static analysis checker and confirmed by manual
source review. |
| A vulnerability was identified in Mullvad wireguard.sys 0.10.1. The affected element is the function AdapterState of the component IOCTL Handler. Such manipulation leads to improper update of reference count. Local access is required to approach this attack. The exploit is publicly available and might be used. The vendor was contacted early about this disclosure. |
| In the Linux kernel, the following vulnerability has been resolved:
ovpn: fix peer refcount leak in TCP error paths
When either the TCP RX or TX error path calls ovpn_peer_hold() followed
by schedule_work(&peer->tcp.defer_del_work), and the work item is already
pending from the other path, schedule_work() returns false and the work
runs only once. Since ovpn_tcp_peer_del_work() calls ovpn_peer_put()
exactly once, the extra reference taken by the losing path is never
dropped, leaking the peer object.
The race window:
CPU0 (strparser/RX error): CPU1 (tcp_tx_work/TX error):
ovpn_peer_hold() <- refcnt+1 ovpn_peer_hold() <- refcnt+2
schedule_work() <- queued schedule_work() <- NO-OP
(work already pending)
ovpn_tcp_peer_del_work runs:
ovpn_peer_del()
ovpn_peer_put() <- refcnt+1
<- peer never freed
Fix by checking the return value of schedule_work() in both paths and
calling ovpn_peer_put() to drop the extra reference if the work was
already pending. ovpn_peer_hold() is kept unconditional in the TX path
as it cannot fail at that point. |
| In the Linux kernel, the following vulnerability has been resolved:
ice: fix PTP Call Trace during PTP release
If a PF reset occurs when the PTP state is ICE_PTP_UNINIT, then
ice_ptp_rebuild() will update the state to ICE_PTP_ERROR. This will
result in the following PTP release call trace during driver unload:
kernel BUG at lib/list_debug.c:52!
ice_ptp_release+0x332/0x3c0 [ice]
ice_deinit_features.part.0+0x10e/0x120 [ice]
ice_remove+0x100/0x220 [ice]
This was observed when passing PF1 through to a VM. ice_ptp_init()
fails because ctrl_pf is NULL and sets the state to ICE_PTP_UNINIT.
Fix by detecting the ICE_PTP_UNINIT state in ice_ptp_rebuild() and
returning without error, preventing the invalid state transition to
ICE_PTP_ERROR. The only valid path to ICE_PTP_ERROR is from
ICE_PTP_RESETTING after a failed rebuild. |
| In the Linux kernel, the following vulnerability has been resolved:
LoongArch: Move jump_label_init() before parse_early_param()
When enabling both CONFIG_MEM_ALLOC_PROFILING=y and
CONFIG_MEM_ALLOC_PROFILING_ENABLED_BY_DEFAULT=y, then diabling memory
profiling by adding the boot parameter 'sysctl.vm.mem_profiling=0' will
cause the kernel failed to boot.
After analysis, this is because jump_label_init() must be called before
parse_early_param(), the early param handlers may modify static keys by
static_branch_enable/disable().
Fix this by moving jump_label_init() to before parse_early_param(). The
solution is similar to other architectures. |
| In the Linux kernel, the following vulnerability has been resolved:
smb/client: Fix error code in smb2_aead_req_alloc()
The "*num_sgs" variable is a u32 so "ERR_PTR(*num_sgs)" doesn't work.
We would have to do something similar to the previous line where it's
cast to int and then long. However, it's simpler to store the return in
an int ret variable.
This bug would eventually result in a crash when dereference the invalid
error pointer. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: adc: spear: Initialize completion before requesting IRQ
In the report from Jaeyoung Chung:
"spear_adc_probe() in drivers/iio/adc/spear_adc.c registers its
interrupt handler with devm_request_irq() before it initializes
st->completion with init_completion(). If an interrupt arrives after
devm_request_irq() and before init_completion(), the handler calls
complete() on an uninitialized completion, causing a kernel panic.
The probe path, in spear_adc_probe():
iodev = devm_iio_device_alloc(&pdev->dev, sizeof(*st)); /* st kzalloc-zeroed */
...
retval = devm_request_irq(&pdev->dev, irq, spear_adc_isr, 0,
LPC32XXAD_NAME, st); /* register handler */
...
init_completion(&st->completion); /* initialize completion */
spear_adc_isr() calls complete():
complete(&st->completion);
If the device raises an interrupt before init_completion() runs,
complete() acquires the uninitialized wait.lock and walks the zeroed
task_list in swake_up_locked(). The zeroed task_list makes list_empty()
return false, so swake_up_locked() dereferences a NULL list entry,
triggering a KASAN wild-memory-access."
Fix the chance of a spurious IRQ causing an uninitialized pointer
dereference by moving init_completion() above devm_request_irq(). |
| Electron is a framework for writing cross-platform desktop applications using JavaScript, HTML and CSS. Prior to 40.10.6, 41.9.1, 42.5.1, and 43.0.0, when a custom protocol handler returned a ProtocolResponse with a url and no session, Electron made the upstream request through defaultSession instead of the session that handled the protocol. A cached response could then be reused across otherwise isolated session partitions. Apps that use ProtocolResponse.url, omit ProtocolResponse.session, and rely on separate sessions to isolate content are affected. This issue is fixed in versions 40.10.6, 41.9.1, 42.5.1, and 43.0.0. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: bpf_local_storage: Always use bpf_mem_alloc in PREEMPT_RT
In PREEMPT_RT, kmalloc(GFP_ATOMIC) is still not safe in non preemptible
context. bpf_mem_alloc must be used in PREEMPT_RT. This patch is
to enforce bpf_mem_alloc in the bpf_local_storage when CONFIG_PREEMPT_RT
is enabled.
[ 35.118559] BUG: sleeping function called from invalid context at kernel/locking/spinlock_rt.c:48
[ 35.118566] in_atomic(): 1, irqs_disabled(): 0, non_block: 0, pid: 1832, name: test_progs
[ 35.118569] preempt_count: 1, expected: 0
[ 35.118571] RCU nest depth: 1, expected: 1
[ 35.118577] INFO: lockdep is turned off.
...
[ 35.118647] __might_resched+0x433/0x5b0
[ 35.118677] rt_spin_lock+0xc3/0x290
[ 35.118700] ___slab_alloc+0x72/0xc40
[ 35.118723] __kmalloc_noprof+0x13f/0x4e0
[ 35.118732] bpf_map_kzalloc+0xe5/0x220
[ 35.118740] bpf_selem_alloc+0x1d2/0x7b0
[ 35.118755] bpf_local_storage_update+0x2fa/0x8b0
[ 35.118784] bpf_sk_storage_get_tracing+0x15a/0x1d0
[ 35.118791] bpf_prog_9a118d86fca78ebb_trace_inet_sock_set_state+0x44/0x66
[ 35.118795] bpf_trace_run3+0x222/0x400
[ 35.118820] __bpf_trace_inet_sock_set_state+0x11/0x20
[ 35.118824] trace_inet_sock_set_state+0x112/0x130
[ 35.118830] inet_sk_state_store+0x41/0x90
[ 35.118836] tcp_set_state+0x3b3/0x640
There is no need to adjust the gfp_flags passing to the
bpf_mem_cache_alloc_flags() which only honors the GFP_KERNEL.
The verifier has ensured GFP_KERNEL is passed only in sleepable context.
It has been an old issue since the first introduction of the
bpf_local_storage ~5 years ago, so this patch targets the bpf-next.
bpf_mem_alloc is needed to solve it, so the Fixes tag is set
to the commit when bpf_mem_alloc was first used in the bpf_local_storage. |
| The import hook in CPython that handles legacy *.pyc files (SourcelessFileLoader) is incorrectly handled in FileLoader (a base class) and so does not use io.open_code() to read the .pyc files. sys.audit handlers for this audit event therefore do not fire. |
| A memory initialization issue was addressed with improved memory handling. This issue is fixed in iOS 26.6 and iPadOS 26.6, macOS Sequoia 15.7.8, macOS Sonoma 14.8.8, macOS Tahoe 26.6, tvOS 26.6, visionOS 26.6, watchOS 26.6. An app may be able to cause unexpected system termination. |
| In the Linux kernel, the following vulnerability has been resolved:
wifi: ath11k: add srng->lock for ath11k_hal_srng_* in monitor mode
ath11k_hal_srng_* should be used with srng->lock to protect srng data.
For ath11k_dp_rx_mon_dest_process() and ath11k_dp_full_mon_process_rx(),
they use ath11k_hal_srng_* for many times but never call srng->lock.
So when running (full) monitor mode, warning will occur:
RIP: 0010:ath11k_hal_srng_dst_peek+0x18/0x30 [ath11k]
Call Trace:
? ath11k_hal_srng_dst_peek+0x18/0x30 [ath11k]
ath11k_dp_rx_process_mon_status+0xc45/0x1190 [ath11k]
? idr_alloc_u32+0x97/0xd0
ath11k_dp_rx_process_mon_rings+0x32a/0x550 [ath11k]
ath11k_dp_service_srng+0x289/0x5a0 [ath11k]
ath11k_pcic_ext_grp_napi_poll+0x30/0xd0 [ath11k]
__napi_poll+0x30/0x1f0
net_rx_action+0x198/0x320
__do_softirq+0xdd/0x319
So add srng->lock for them to avoid such warnings.
Inorder to fetch the srng->lock, should change srng's definition from
'void' to 'struct hal_srng'. And initialize them elsewhere to prevent
one line of code from being too long. This is consistent with other ring
process functions, such as ath11k_dp_process_rx().
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.30
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1 |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: fix racy issue from session lookup and expire
Increment the session reference count within the lock for lookup to avoid
racy issue with session expire. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/amdgpu: Add a lock when accessing the buddy trim function
When running YouTube videos and Steam games simultaneously,
the tester found a system hang / race condition issue with
the multi-display configuration setting. Adding a lock to
the buddy allocator's trim function would be the solution.
<log snip>
[ 7197.250436] general protection fault, probably for non-canonical address 0xdead000000000108
[ 7197.250447] RIP: 0010:__alloc_range+0x8b/0x340 [amddrm_buddy]
[ 7197.250470] Call Trace:
[ 7197.250472] <TASK>
[ 7197.250475] ? show_regs+0x6d/0x80
[ 7197.250481] ? die_addr+0x37/0xa0
[ 7197.250483] ? exc_general_protection+0x1db/0x480
[ 7197.250488] ? drm_suballoc_new+0x13c/0x93d [drm_suballoc_helper]
[ 7197.250493] ? asm_exc_general_protection+0x27/0x30
[ 7197.250498] ? __alloc_range+0x8b/0x340 [amddrm_buddy]
[ 7197.250501] ? __alloc_range+0x109/0x340 [amddrm_buddy]
[ 7197.250506] amddrm_buddy_block_trim+0x1b5/0x260 [amddrm_buddy]
[ 7197.250511] amdgpu_vram_mgr_new+0x4f5/0x590 [amdgpu]
[ 7197.250682] amdttm_resource_alloc+0x46/0xb0 [amdttm]
[ 7197.250689] ttm_bo_alloc_resource+0xe4/0x370 [amdttm]
[ 7197.250696] amdttm_bo_validate+0x9d/0x180 [amdttm]
[ 7197.250701] amdgpu_bo_pin+0x15a/0x2f0 [amdgpu]
[ 7197.250831] amdgpu_dm_plane_helper_prepare_fb+0xb2/0x360 [amdgpu]
[ 7197.251025] ? try_wait_for_completion+0x59/0x70
[ 7197.251030] drm_atomic_helper_prepare_planes.part.0+0x2f/0x1e0
[ 7197.251035] drm_atomic_helper_prepare_planes+0x5d/0x70
[ 7197.251037] drm_atomic_helper_commit+0x84/0x160
[ 7197.251040] drm_atomic_nonblocking_commit+0x59/0x70
[ 7197.251043] drm_mode_atomic_ioctl+0x720/0x850
[ 7197.251047] ? __pfx_drm_mode_atomic_ioctl+0x10/0x10
[ 7197.251049] drm_ioctl_kernel+0xb9/0x120
[ 7197.251053] ? srso_alias_return_thunk+0x5/0xfbef5
[ 7197.251056] drm_ioctl+0x2d4/0x550
[ 7197.251058] ? __pfx_drm_mode_atomic_ioctl+0x10/0x10
[ 7197.251063] amdgpu_drm_ioctl+0x4e/0x90 [amdgpu]
[ 7197.251186] __x64_sys_ioctl+0xa0/0xf0
[ 7197.251190] x64_sys_call+0x143b/0x25c0
[ 7197.251193] do_syscall_64+0x7f/0x180
[ 7197.251197] ? srso_alias_return_thunk+0x5/0xfbef5
[ 7197.251199] ? amdgpu_display_user_framebuffer_create+0x215/0x320 [amdgpu]
[ 7197.251329] ? drm_internal_framebuffer_create+0xb7/0x1a0
[ 7197.251332] ? srso_alias_return_thunk+0x5/0xfbef5
(cherry picked from commit 3318ba94e56b9183d0304577c74b33b6b01ce516) |
| In the Linux kernel, the following vulnerability has been resolved:
ksmbd: set ATTR_CTIME flags when setting mtime
David reported that the new warning from setattr_copy_mgtime is coming
like the following.
[ 113.215316] ------------[ cut here ]------------
[ 113.215974] WARNING: CPU: 1 PID: 31 at fs/attr.c:300 setattr_copy+0x1ee/0x200
[ 113.219192] CPU: 1 UID: 0 PID: 31 Comm: kworker/1:1 Not tainted 6.13.0-rc1+ #234
[ 113.220127] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.2-3-gd478f380-rebuilt.opensuse.org 04/01/2014
[ 113.221530] Workqueue: ksmbd-io handle_ksmbd_work [ksmbd]
[ 113.222220] RIP: 0010:setattr_copy+0x1ee/0x200
[ 113.222833] Code: 24 28 49 8b 44 24 30 48 89 53 58 89 43 6c 5b 41 5c 41 5d 41 5e 41 5f 5d c3 cc cc cc cc 48 89 df e8 77 d6 ff ff e9 cd fe ff ff <0f> 0b e9 be fe ff ff 66 0
[ 113.225110] RSP: 0018:ffffaf218010fb68 EFLAGS: 00010202
[ 113.225765] RAX: 0000000000000120 RBX: ffffa446815f8568 RCX: 0000000000000003
[ 113.226667] RDX: ffffaf218010fd38 RSI: ffffa446815f8568 RDI: ffffffff94eb03a0
[ 113.227531] RBP: ffffaf218010fb90 R08: 0000001a251e217d R09: 00000000675259fa
[ 113.228426] R10: 0000000002ba8a6d R11: ffffa4468196c7a8 R12: ffffaf218010fd38
[ 113.229304] R13: 0000000000000120 R14: ffffffff94eb03a0 R15: 0000000000000000
[ 113.230210] FS: 0000000000000000(0000) GS:ffffa44739d00000(0000) knlGS:0000000000000000
[ 113.231215] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 113.232055] CR2: 00007efe0053d27e CR3: 000000000331a000 CR4: 00000000000006b0
[ 113.232926] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 113.233812] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 113.234797] Call Trace:
[ 113.235116] <TASK>
[ 113.235393] ? __warn+0x73/0xd0
[ 113.235802] ? setattr_copy+0x1ee/0x200
[ 113.236299] ? report_bug+0xf3/0x1e0
[ 113.236757] ? handle_bug+0x4d/0x90
[ 113.237202] ? exc_invalid_op+0x13/0x60
[ 113.237689] ? asm_exc_invalid_op+0x16/0x20
[ 113.238185] ? setattr_copy+0x1ee/0x200
[ 113.238692] btrfs_setattr+0x80/0x820 [btrfs]
[ 113.239285] ? get_stack_info_noinstr+0x12/0xf0
[ 113.239857] ? __module_address+0x22/0xa0
[ 113.240368] ? handle_ksmbd_work+0x6e/0x460 [ksmbd]
[ 113.240993] ? __module_text_address+0x9/0x50
[ 113.241545] ? __module_address+0x22/0xa0
[ 113.242033] ? unwind_next_frame+0x10e/0x920
[ 113.242600] ? __pfx_stack_trace_consume_entry+0x10/0x10
[ 113.243268] notify_change+0x2c2/0x4e0
[ 113.243746] ? stack_depot_save_flags+0x27/0x730
[ 113.244339] ? set_file_basic_info+0x130/0x2b0 [ksmbd]
[ 113.244993] set_file_basic_info+0x130/0x2b0 [ksmbd]
[ 113.245613] ? process_scheduled_works+0xbe/0x310
[ 113.246181] ? worker_thread+0x100/0x240
[ 113.246696] ? kthread+0xc8/0x100
[ 113.247126] ? ret_from_fork+0x2b/0x40
[ 113.247606] ? ret_from_fork_asm+0x1a/0x30
[ 113.248132] smb2_set_info+0x63f/0xa70 [ksmbd]
ksmbd is trying to set the atime and mtime via notify_change without also
setting the ctime. so This patch add ATTR_CTIME flags when setting mtime
to avoid a warning. |
| In the Linux kernel, the following vulnerability has been resolved:
mm: hugetlb: independent PMD page table shared count
The folio refcount may be increased unexpectly through try_get_folio() by
caller such as split_huge_pages. In huge_pmd_unshare(), we use refcount
to check whether a pmd page table is shared. The check is incorrect if
the refcount is increased by the above caller, and this can cause the page
table leaked:
BUG: Bad page state in process sh pfn:109324
page: refcount:0 mapcount:0 mapping:0000000000000000 index:0x66 pfn:0x109324
flags: 0x17ffff800000000(node=0|zone=2|lastcpupid=0xfffff)
page_type: f2(table)
raw: 017ffff800000000 0000000000000000 0000000000000000 0000000000000000
raw: 0000000000000066 0000000000000000 00000000f2000000 0000000000000000
page dumped because: nonzero mapcount
...
CPU: 31 UID: 0 PID: 7515 Comm: sh Kdump: loaded Tainted: G B 6.13.0-rc2master+ #7
Tainted: [B]=BAD_PAGE
Hardware name: QEMU KVM Virtual Machine, BIOS 0.0.0 02/06/2015
Call trace:
show_stack+0x20/0x38 (C)
dump_stack_lvl+0x80/0xf8
dump_stack+0x18/0x28
bad_page+0x8c/0x130
free_page_is_bad_report+0xa4/0xb0
free_unref_page+0x3cc/0x620
__folio_put+0xf4/0x158
split_huge_pages_all+0x1e0/0x3e8
split_huge_pages_write+0x25c/0x2d8
full_proxy_write+0x64/0xd8
vfs_write+0xcc/0x280
ksys_write+0x70/0x110
__arm64_sys_write+0x24/0x38
invoke_syscall+0x50/0x120
el0_svc_common.constprop.0+0xc8/0xf0
do_el0_svc+0x24/0x38
el0_svc+0x34/0x128
el0t_64_sync_handler+0xc8/0xd0
el0t_64_sync+0x190/0x198
The issue may be triggered by damon, offline_page, page_idle, etc, which
will increase the refcount of page table.
1. The page table itself will be discarded after reporting the
"nonzero mapcount".
2. The HugeTLB page mapped by the page table miss freeing since we
treat the page table as shared and a shared page table will not be
unmapped.
Fix it by introducing independent PMD page table shared count. As
described by comment, pt_index/pt_mm/pt_frag_refcount are used for s390
gmap, x86 pgds and powerpc, pt_share_count is used for x86/arm64/riscv
pmds, so we can reuse the field as pt_share_count. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: mpi3mr: Fix corrupt config pages PHY state is switched in sysfs
The driver, through the SAS transport, exposes a sysfs interface to
enable/disable PHYs in a controller/expander setup. When multiple PHYs
are disabled and enabled in rapid succession, the persistent and current
config pages related to SAS IO unit/SAS Expander pages could get
corrupted.
Use separate memory for each config request. |
| In the Linux kernel, the following vulnerability has been resolved:
net: stmmac: fix TSO DMA API usage causing oops
Commit 66600fac7a98 ("net: stmmac: TSO: Fix unbalanced DMA map/unmap
for non-paged SKB data") moved the assignment of tx_skbuff_dma[]'s
members to be later in stmmac_tso_xmit().
The buf (dma cookie) and len stored in this structure are passed to
dma_unmap_single() by stmmac_tx_clean(). The DMA API requires that
the dma cookie passed to dma_unmap_single() is the same as the value
returned from dma_map_single(). However, by moving the assignment
later, this is not the case when priv->dma_cap.addr64 > 32 as "des"
is offset by proto_hdr_len.
This causes problems such as:
dwc-eth-dwmac 2490000.ethernet eth0: Tx DMA map failed
and with DMA_API_DEBUG enabled:
DMA-API: dwc-eth-dwmac 2490000.ethernet: device driver tries to +free DMA memory it has not allocated [device address=0x000000ffffcf65c0] [size=66 bytes]
Fix this by maintaining "des" as the original DMA cookie, and use
tso_des to pass the offset DMA cookie to stmmac_tso_allocator().
Full details of the crashes can be found at:
https://lore.kernel.org/all/d8112193-0386-4e14-b516-37c2d838171a@nvidia.com/
https://lore.kernel.org/all/klkzp5yn5kq5efgtrow6wbvnc46bcqfxs65nz3qy77ujr5turc@bwwhelz2l4dw/ |
| In the Linux kernel, the following vulnerability has been resolved:
bpf: fix recursive lock when verdict program return SK_PASS
When the stream_verdict program returns SK_PASS, it places the received skb
into its own receive queue, but a recursive lock eventually occurs, leading
to an operating system deadlock. This issue has been present since v6.9.
'''
sk_psock_strp_data_ready
write_lock_bh(&sk->sk_callback_lock)
strp_data_ready
strp_read_sock
read_sock -> tcp_read_sock
strp_recv
cb.rcv_msg -> sk_psock_strp_read
# now stream_verdict return SK_PASS without peer sock assign
__SK_PASS = sk_psock_map_verd(SK_PASS, NULL)
sk_psock_verdict_apply
sk_psock_skb_ingress_self
sk_psock_skb_ingress_enqueue
sk_psock_data_ready
read_lock_bh(&sk->sk_callback_lock) <= dead lock
'''
This topic has been discussed before, but it has not been fixed.
Previous discussion:
https://lore.kernel.org/all/6684a5864ec86_403d20898@john.notmuch |
