| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
i2c: imx: fix locked bus on SMBus block-read of 0 (atomic)
SMBus 3.1 6.5.7 allows a Block Read byte count of 0, but the atomic
(polling) path rejects it as -EPROTO. Worse, it returns without a
NACK+STOP: the next receive cycle has already started, so the target
keeps holding SDA and the bus stays stuck until a power cycle for
this i2c controller.
Reading I2DR to obtain the count likewise arms the next byte on the
count > I2C_SMBUS_BLOCK_MAX path, which also returned -EPROTO directly
and left the bus held.
Handle both: NACK the in-flight dummy byte (TXAK) and extend msgs->len so
the existing last-byte handling emits STOP; the dummy byte is discarded.
A count of 0 is a valid empty block read; a count above
I2C_SMBUS_BLOCK_MAX is still reported as -EPROTO, but only after the bus
has been released.
The interrupt-driven path has the same flaw from a later commit and is
fixed separately, as it carries a different Fixes: tag and stable range. |
| In the Linux kernel, the following vulnerability has been resolved:
scsi: elx: efct: Fix I/O leak on unsupported additional CDB
efct_dispatch_fcp_cmd() allocates an efct_io before dispatching an
unsolicited FCP command. If the command has an unsupported additional
CDB, the function returns -EIO before handing the IO to the SCSI layer.
Free the allocated IO before returning from this error path. |
| In the Linux kernel, the following vulnerability has been resolved:
irqchip/irq-riscv-imsic-early: Fix fwnode leak on state setup failure
imsic_early_acpi_init() allocates a firmware node before setting up the
IMSIC state. If imsic_setup_state() fails, the function returns without
freeing the allocated fwnode.
Free the fwnode and clear the global pointer on this error path, matching
the cleanup already done when imsic_early_probe() fails.
[ tglx: Use a common cleanup path instead of copying code around ] |
| In the Linux kernel, the following vulnerability has been resolved:
net: macb: drop in-flight Tx SKBs on close
The MACB driver has since forever leaked the outgoing SKBs that
have not yet been marked as completed. They live in queue->tx_skb
which gets freed without remorse nor checking.
macb_free_consistent() gets called in a few codepaths, but only close will
trigger the added expressions. In macb_open() and macb_alloc_consistent()
failure cases, queues' tx_skb just got allocated and are empty. |
| In the Linux kernel, the following vulnerability has been resolved:
net/mlx5: free mlx5_st_idx_data on final dealloc
Workloads that repeatedly allocate and release mkeys carrying TPH
steering-tag hints (e.g. churning RDMA MRs) leak one
struct mlx5_st_idx_data per cycle; kmemleak flags it as unreferenced
and the kmalloc slab grows over time.
When the last reference to an ST table entry is dropped,
mlx5_st_dealloc_index() removed the entry from idx_xa but the backing
mlx5_st_idx_data allocation was never freed.
Free idx_data after the xa_erase() so the lifetime of the bookkeeping
struct matches the lifetime of the ST entry it tracks. |
| In the Linux kernel, the following vulnerability has been resolved:
reset: sunxi: fix memory region leak on ioremap failure
In sunxi_reset_init(), when ioremap() fails, the memory region obtained
via request_mem_region() is not released, leading to a resource leak.
Add an err_mem_region label to properly release the memory region before
freeing the data structure. |
| In the Linux kernel, the following vulnerability has been resolved:
mtd: virt-concat: free duplicate generated name
Every MTD registration runs mtd_virt_concat_create_join(). Once a
virtual concat has already been registered, the function builds the same
name again and takes the equal-name branch. That branch skips to the
next item without freeing the newly allocated string.
Free the temporary name before continuing. |
| A malicious SSH peer could send unsolicited global request responses to fill an internal buffer, blocking the connection's read loop. The blocked goroutine could not be released by calling Close(), resulting in a resource leak per connection. Unsolicited global responses are now discarded. |
| In the Linux kernel, the following vulnerability has been resolved:
sctp: close UDP tunnel sockets during netns teardown
proc_sctp_do_udp_port() starts per-net SCTP UDP tunneling sockets when
net.sctp.udp_port is set, and stops/restarts them when the sysctl value
changes. The netns exit path does not stop these sockets, so a namespace
can be torn down while its SCTP UDP tunnel sockets are still installed.
Close the UDP tunnel sockets from sctp_ctrlsock_exit() after unregistering
the per-net sysctl table. This prevents new sysctl writes from racing in
while the sockets are being released, and closes the sockets before the
control socket is destroyed. |
| In the Linux kernel, the following vulnerability has been resolved:
iio: sca3000: Fix a resource leak in sca3000_probe()
spi->irq from request_threaded_irq() not released when
iio_device_register() fails. Add an return value check and jump to a
common error handler when iio_device_register() fails. |
| In the Linux kernel, the following vulnerability has been resolved:
zram: do not forget to endio for partial discard requests
As reported by Qu Wenruo and Avinesh Kumar, the following
getconf PAGESIZE
65536
blkdiscard -p 4k /dev/zram0
takes literally forever to complete. zram doesn't support partial
discards and just returns immediately w/o doing any discard work in such
cases. The problem is that we forget to endio on our way out, so
blkdiscard sleeps forever in submit_bio_wait(). Fix this by jumping to
end_bio label, which does bio_endio(). |
| In the Linux kernel, the following vulnerability has been resolved:
can: ucan: fix devres lifetime
USB drivers bind to USB interfaces and any device managed resources
should have their lifetime tied to the interface rather than parent USB
device. This avoids issues like memory leaks when drivers are unbound
without their devices being physically disconnected (e.g. on probe
deferral or configuration changes).
Fix the control message buffer lifetime so that it is released on driver
unbind. |
| In the Linux kernel, the following vulnerability has been resolved:
net: mctp i3c: clean up notifier and buses if driver register fails
mctp_i3c_mod_init() registers the I3C bus notifier and then walks the
existing buses with i3c_for_each_bus_locked(mctp_i3c_bus_add_new, NULL)
before registering the I3C device driver. If i3c_driver_register()
fails, the function returns the error directly, leaving the notifier
registered and every mctp_i3c_bus object created for the existing buses
allocated. The notifier is left pointing into the module that failed to
load and the bus list is leaked.
Mirror the module exit path on this failure: unregister the notifier and
tear down the buses that were added before returning the error.
This issue was identified during our ongoing static-analysis research while
reviewing kernel code. |
| In the Linux kernel, the following vulnerability has been resolved:
drm/xe/vm: Fix SVM leak on resv obj alloc failure in xe_vm_create()
Commit 9e9787414882 ("drm/xe/userptr: replace xe_hmm with gpusvm") made
xe_svm_init() unconditional in xe_vm_create() and extended it to also
initialize a "simple" gpusvm state for non-fault-mode VMs. The matching
xe_svm_fini() call in xe_vm_close_and_put() was updated to run
unconditionally, but the error unwind path in xe_vm_create() was not.
On the drm_gpuvm_resv_object_alloc() failure path, xe_svm_init() has
already succeeded but xe_svm_fini() is only called when
XE_VM_FLAG_FAULT_MODE is set. For non-fault-mode VMs this leaves
vm->svm.gpusvm partially initialized and leaks the resources allocated
by drm_gpusvm_init().
For fault-mode VMs, xe_svm_init() additionally acquires the pagemap
owner via drm_pagemap_acquire_owner() and the pagemaps via
xe_svm_get_pagemaps(). Those resources are released by xe_svm_close(),
not xe_svm_fini(). On the same error path, xe_svm_close() is not
called either, so fault-mode VMs leak the pagemap owner and pagemaps.
Fix both leaks:
- Call xe_svm_fini() unconditionally on the err_svm_fini path, matching
the unconditional xe_svm_init() call. Move the vm->size = 0
assignment out of the conditional so the xe_vm_is_closed() assert in
xe_svm_fini() (and xe_svm_close()) holds for both modes.
- Call xe_svm_close() for fault-mode VMs before xe_svm_fini(), matching
the ordering used in xe_vm_close_and_put().
(cherry picked from commit ca2a3587d577ba764e0fe628fb676244fc33ddd4) |
| In the Linux kernel, the following vulnerability has been resolved:
drm/gpusvm: publish dpagemap early to avoid device mapping leak on error
drm_gpusvm_get_pages() only stored the local dpagemap into
svm_pages->dpagemap on the success path. If a later page failed (e.g.
-EOPNOTSUPP when ctx->allow_mixed is false) and jumped to err_unmap,
svm_pages->dpagemap was still NULL, so __drm_gpusvm_unmap_pages() skipped
device_unmap() and leaked the device mappings already created.
Assign svm_pages->dpagemap when the first device page is mapped so the
err_unmap path can device_unmap() those mappings.
This issue was found by Sashiko AI review. |
| Netty is an asynchronous, event-driven network application framework. Prior to 4.1.136.Final and 4.2.16.Final, io.netty.handler.codec.dns.AbstractDnsRecord, io.netty.handler.codec.dns.DefaultDnsRecordDecoder.decodeRecord(), and io.netty.handler.codec.dns.DnsCodecUtil.decompressDomainName() failed to release retained or newly allocated ByteBuf objects when IDN.toASCII() or encodeDomainName() rejected a malformed domain name, allowing unauthenticated remote DNS packets to leak direct memory incrementally until denial of service. This issue is fixed in versions 4.1.136.Final and 4.2.16.Final. |
| Klever-Go is the Go implementation of the Klever blockchain protocol. In versions prior to 1.7.18, the account-data trie syncers are vulnerable to a resource-exhaustion flaw that leaks bounded throttler slots on error paths. In syncDataTrie() (in both userAccountsSyncer.go and kappAccountsSyncer.go), StartProcessing() reserves a slot from the NumGoRoutinesThrottler, but the corresponding EndProcessing() is only called on the success path and on the duplicate-root early return. As a result, any error from trie.NewTrie(), trie.NewTrieSyncer(), or trieSyncer.StartSyncing() (including the network-dependent timeout path) permanently consumes one slot for the lifetime of the throttler. An attacker who can repeatedly cause trie-node sync failures or timeouts during bootstrap can exhaust the bounded throttler, after which further account-data trie syncs stop making progress and SyncAccounts() returns a timeout. Because epoch bootstrap in syncUserAccountsState() and syncKappAccountsState() aborts on any such error, this causes bootstrap to fail, a core availability issue affecting fresh, restarting, or resyncing nodes and validators. This issue is fixed in version 1.7.18. |
| In the Linux kernel, the following vulnerability has been resolved:
gpio: rockchip: teardown bugs and resource leaks
Address several teardown issues and resource leaks in the driver's remove
path and error handling:
1. Debounce clock reference leak: The debounce clock (bank->db_clk) is
obtained using of_clk_get() which increments the clock's reference
count, but clk_put() is never called. Register a devm action to
cleanly release it on unbind. Note that of_clk_get(..., 1) remains
necessary over devm_clk_get() because the DT binding does not define
clock-names, precluding name-based lookup.
2. Unregistered chained IRQ handler: The chained IRQ handler is not
disconnected in remove(). If a stray interrupt fires after the driver
is removed, the kernel attempts to execute a stale handler, leading
to a panic. Fix this by clearing the handler in remove().
3. IRQ domain leak: The linear IRQ domain and its generic chips are
allocated manually during probe but never removed. Remove the IRQ
domain during driver teardown to free the associated generic chips
and mappings.
[Bartosz: don't emit an error message on devres allocation failure] |
| HttpClient based on the classic i/o model fails to correctly release the underlying connection back to the connection manager if it encounters an invalid or unsupported `Content-Encoding` header value in the response message. Please note this defect does not affect HttpClient based on the async i/o model.
This issue affects Apache HttpComponents Client: from 5.0-alpha1 through 5.6.2. |
| In the Linux kernel, the following vulnerability has been resolved:
svcrdma: wake sq waiters when the transport closes
Threads parked in svc_rdma_sq_wait() on sc_sq_ticket_wait or
sc_send_wait can hang indefinitely in TASK_UNINTERRUPTIBLE state
across transport teardown, pinning svc_xprt references and
blocking svc_rdma_free().
The close path sets XPT_CLOSE before invoking xpo_detach and both
wait_event predicates include an XPT_CLOSE term, but the
predicates are re-evaluated only on wakeup. sc_sq_ticket_wait has
no completion-driven wake path; it is advanced solely by the
chained ticket handoff inside svc_rdma_sq_wait() itself. Without
an explicit wake at close, parked threads never observe
XPT_CLOSE, hold their svc_xprt_get reference forever, and
svc_rdma_free() blocks on xpt_ref dropping to zero.
Two close entry points reach this transport. Local teardown runs
svc_rdma_detach() from svc_handle_xprt() -> svc_delete_xprt() ->
xpo_detach() on a worker thread. A remote disconnect arrives at
svc_rdma_cma_handler(), which calls svc_xprt_deferred_close():
that sets XPT_CLOSE and enqueues the transport but does not
access either RDMA waitqueue, so a worker already parked in
svc_rdma_sq_wait() never re-evaluates its predicate. With every
worker parked on this transport, no thread is available to run
the local teardown either, and the wake site there is
unreachable.
Introduce svc_rdma_xprt_deferred_close(), a thin svcrdma wrapper
that calls svc_xprt_deferred_close() and then wakes both
sc_sq_ticket_wait and sc_send_wait. Convert the svcrdma producers
that called svc_xprt_deferred_close() directly:
svc_rdma_cma_handler(), qp_event_handler(),
svc_rdma_post_send_err(), svc_rdma_wc_send(), the sendto drop
path, the rw completion error paths, and the recvfrom flush and
read-list error paths.
Wake both waitqueues from svc_rdma_detach() as well. The
synchronous svc_xprt_close() path (backchannel ENOTCONN, device
removal via svc_rdma_xprt_done) reaches detach without flowing
through svc_xprt_deferred_close() and therefore does not invoke
the new helper.
[ cel: add svc_rdma_xprt_deferred_close() to complete the fix ] |
