| CVE |
Vendors |
Products |
Updated |
CVSS v3.1 |
| In the Linux kernel, the following vulnerability has been resolved:
net/atm: fix slab-out-of-bounds read in vcc_setsockopt()
vcc_setsockopt() contained an ineffective optlen check:
if (__SO_LEVEL_MATCH(optname, level) && optlen != __SO_SIZE(optname))
return -EINVAL;
If __SO_LEVEL_MATCH(optname, level) evaluated to false (e.g. if the caller
passed a mismatched level), the length check optlen != __SO_SIZE(optname)
was short-circuited and bypassed. Execution then fell through to switch(optname),
calling copy_from_sockptr() assuming optval contained sufficient space.
Furthermore, even if level matched, a cgroup BPF setsockopt filter could shrink
optlen after entry. Because copy_from_sockptr() on kernel pointers uses memcpy(),
this leads to a KASAN slab-out-of-bounds read when optlen is smaller than the
expected structure size.
Fix this by using copy_safe_from_sockptr(), which unconditionally validates
that optlen is at least the expected size before copying. Also change the local
'value' variable type from 'unsigned long' to 'int' so that SO_SETCLP matches
its sizeof(int) ABI encoding on 64-bit systems. |
| In the Linux kernel, the following vulnerability has been resolved:
mac802154: fix netdev use-after-free in beacon worker
mac802154_beacon_worker() reads local->beacon_req under RCU and derives
the sub-interface from the request, but then drops the RCU read lock and
continues to use both sdata and the embedded wpan_dev.
mac802154_stop_beacons_locked() cancels only pending beacon work, clears
local->beacon_req and frees the request. A beacon worker that is already
running can therefore continue after interface teardown and dereference
the freed netdev private area.
The scan worker already pins the netdev before leaving RCU. Apply the
same lifetime rule to the beacon worker: take a netdev reference while
the request is still protected by RCU, and release it on all paths that
continue after the reference is acquired. |
| In the Linux kernel, the following vulnerability has been resolved:
ipv4: Fix fib_nlmsg_size() for RTA_VIA nexthops
fib_nlmsg_size() still estimates nexthop space as if every gateway is
encoded as an IPv4 RTA_GATEWAY attribute. IPv4 routes can also carry an
IPv6 gateway, which fib_nexthop_info() dumps as RTA_VIA.
As a result, route notifications can allocate an skb that is too small.
fib_dump_info() then fails with -EMSGSIZE and rtmsg_fib() hits the
WARN_ON() that marks such failures as a fib_nlmsg_size() bug. With
panic_on_warn set, this becomes a kernel panic.
Mirror the actual nexthop dump layout in fib_nlmsg_size(): account for
IPv6 nexthop gateways dumped as RTA_VIA, for the no-header rtnexthop
layout used inside RTA_MULTIPATH, and for RTA_FLOW only when it is
actually present. |
| In the Linux kernel, the following vulnerability has been resolved:
serial: 8250_dma: Clear stale RX state on shutdown
serial8250_release_dma() terminates RX DMA and releases the channel, but
leaves rx_running set. If the port is closed while an RX transfer is
active, the stale state remains while rxchan is NULL until the channel is
requested again on the next open.
The DesignWare BUSY workaround added by commit a7b9ce39fbe4
("serial: 8250_dw: Ensure BUSY is deasserted") calls
serial8250_rx_dma_flush() from the LCR write path during startup. This
happens before serial8250_request_dma() obtains a new RX channel. On
reopen, the stale rx_running state therefore makes the flush path pass a
NULL channel to dmaengine_pause(), causing a kernel Oops.
Clear rx_running after terminating RX DMA, matching the TX cleanup. Also
make the flush helper return if the DMA object or RX channel is not
available so startup and teardown paths cannot pass a NULL channel to the
DMAengine API. |
| In the Linux kernel, the following vulnerability has been resolved:
staging: rtl8723bs: validate monitor transmit frame lengths
rtw_cfg80211_monitor_if_xmit_entry() removes the radiotap header and
then reads the 802.11 frame control field without checking that a base
802.11 header remains.
The data path also pulls the calculated 802.11, QoS and SNAP header
span before confirming that the skb contains it. A truncated frame can
therefore cause out-of-bounds reads or leave insufficient data for the
Ethernet address writes.
Reject frames that do not contain the base 802.11 header and data
frames that do not contain their complete calculated header span. |
| In the Linux kernel, the following vulnerability has been resolved:
ALSA: usx2y: bound the hwdep mmap fault offset
snd_us428ctls_vm_fault() turns the faulting page offset into a kernel
address with no bound of any kind:
offset = vmf->pgoff << PAGE_SHIFT;
vaddr = (char *)(...)->us428ctls_sharedmem + offset;
page = virt_to_page(vaddr);
get_page(page);
vmf->page = page;
return 0;
snd_us428ctls_mmap() checks only the length of the mapping, never the
offset, and us428ctls_sharedmem is a single page from
alloc_pages_exact(). For a character device file_mmap_size_max()
returns ULONG_MAX, so the mm layer imposes no ceiling either. Every page
offset above zero resolves to a struct page outside the object, and the
handler installs it into the caller's address space read-write; the vma
is not marked read-only.
The caller picks the page frame with a single mmap() argument and gets
read-write access to a page of kernel memory it does not own; an offset
that lands in an unpopulated vmemmap region oopses instead.
A process that can open the hwdep node of an attached US-X2Y reaches
this after loading the FPGA image through the same node; no capability
check is involved.
On 7.2.0-rc5 (arm64), mmap() with a large offset:
Unable to handle kernel paging request at virtual address fffffdffc45d5ac8
pc : snd_us428ctls_vm_fault+0x68/0x140 [snd_usb_usx2y]
Call trace:
snd_us428ctls_vm_fault+0x68/0x140 [snd_usb_usx2y]
__do_fault
__handle_mm_fault
handle_mm_fault
el0_da
Reject any offset outside the shared region. The pcm hwdep handler in
usx2yhwdeppcm.c computes its address the same way and needs the same
bound.
Discovered by XBOW, triaged by Baul Lee <baul.lee@xbow.com> |
| In the Linux kernel, the following vulnerability has been resolved:
tipc: read le->link under the node lock in tipc_node_link_down()
tipc_node_link_down() caches the link pointer before taking n->lock:
struct tipc_link *l = le->link; /* unlocked */
if (!l)
return;
tipc_node_write_lock(n);
if (!tipc_link_is_establishing(l)) { /* deref l */
...
tipc_link_reset(l); /* write into l */
if (delete) {
kfree(l);
le->link = NULL;
The delete=true caller frees that very object under n->lock, so the lock
does not protect the cached pointer against it:
- CPU A, delete=false: tipc_rcv() on TIPC_LINK_DOWN_EVT, or the link
supervision timer via tipc_node_timeout(), reads l unlocked and then
dereferences it under n->lock;
- CPU B, delete=true: netlink TIPC_NL_BEARER_DISABLE -> bearer_disable()
-> tipc_node_delete_links() -> tipc_node_link_down(n, bearer_id, true)
-> kfree(l).
The link is freed with plain kfree(), not kfree_rcu(), and for UDP bearers
disable_media() only schedules the asynchronous cleanup_bearer() work, so
its synchronize_net() runs after the links are already gone. An in-flight
CPU A that has read l therefore dereferences freed memory once B frees it:
a use-after-free read in tipc_link_is_establishing(), and a use-after-free
write via tipc_link_reset() on the establishing branch.
The following trace was captured on 7.2.0-rc5-00284-gaf39eb111ce6:
BUG: KASAN: slab-use-after-free in tipc_link_is_establishing (net/tipc/link.c:285)
Read of size 4 at addr ffff88802e2aa068 by task swapper/2/0
tipc_link_is_establishing (net/tipc/link.c:285)
tipc_node_link_down (net/tipc/node.c:1076)
tipc_node_timeout (net/tipc/node.c:843)
Allocated by task 9549:
tipc_link_create (net/tipc/link.c:490)
tipc_node_check_dest (net/tipc/node.c:1279)
tipc_disc_rcv (net/tipc/discover.c:252)
tipc_udp_recv (net/tipc/udp_media.c:389)
Freed by task 9549:
tipc_node_link_down (net/tipc/node.c:1084)
tipc_node_delete_links (net/tipc/node.c:1320)
bearer_disable (net/tipc/bearer.c:414)
__tipc_nl_bearer_disable (net/tipc/bearer.c:992)
Move the le->link read inside tipc_node_write_lock(), so it is serialised
against the kfree() in the delete path. A racing teardown now either has
not run yet, and we see a valid link, or has already run, and we see NULL. |
| In the Linux kernel, the following vulnerability has been resolved:
fs,fsverity: remove check for fsverity being enabled in setattr_prepare()
The check that fs-verity is available in the kernel is not necessary
here. Filesystems could have fsverity files even without fs-verity
enabled. In that case, truncate on fsverity file will succeed, what this
check is trying to prevent. |
| In the Linux kernel, the following vulnerability has been resolved:
bpf, sockmap: Fix sk_redir use-after-free in send verdict
sk_psock_msg_verdict() takes a socket reference for psock->sk_redir.
tcp_bpf_send_verdict() copies that pointer while holding the source socket
lock, but does not take a reference for the local copy before dropping the
lock around tcp_bpf_sendmsg_redir().
When apply_bytes keeps the cached verdict active, another sendmsg() on the
same source socket can consume the remaining bytes and release the cached
reference while the first thread still holds only the raw local pointer:
CPU 0 CPU 1
sk_redir = psock->sk_redir
apply_bytes remains nonzero
release_sock(sk)
lock_sock(sk)
apply_bytes reaches zero
psock->sk_redir = NULL
release_sock(sk)
tcp_bpf_sendmsg_redir(sk_redir)
sock_put(sk_redir)
tcp_bpf_sendmsg_redir(sk_redir)
The final sock_put() can free sk_redir before CPU 0 dereferences it.
KASAN reported:
BUG: KASAN: slab-use-after-free in tcp_bpf_sendmsg_redir+0xf39/0x1020
Read of size 8 at addr ffff888108537090 by task poc/87
Call Trace:
tcp_bpf_sendmsg_redir+0xf39/0x1020
tcp_bpf_sendmsg+0x977/0x1a50
__sys_sendto+0x32c/0x3a0
__x64_sys_sendto+0xdb/0x1b0
Allocated by task 85:
sk_prot_alloc+0x56/0x210
sk_clone+0x6f/0x14b0
inet_csk_clone_lock+0x24/0x740
tcp_create_openreq_child+0x25/0x2710
tcp_v4_syn_recv_sock+0x10a/0xe00
Freed by task 0:
__kasan_slab_free+0x43/0x70
slab_free_after_rcu_debug+0xa6/0x1e0
rcu_core+0x50a/0x1850
Last potentially related work creation:
__sk_destruct+0x3da/0x540
sk_psock_destroy+0x81e/0xab0
process_one_work+0x63a/0x1070
Take a temporary socket reference while the source socket lock still
protects psock->sk_redir, and drop it after tcp_bpf_sendmsg_redir()
returns. This keeps each unlocked use independent of cached-verdict
ownership. |
| In the Linux kernel, the following vulnerability has been resolved:
RDMA/bnxt_re: zero shared page before exposing to userspace
bnxt_re_alloc_ucontext() allocates uctx->shpg via
__get_free_page(GFP_KERNEL). The buddy allocator does not zero pages
without __GFP_ZERO, so the page contains stale kernel data from
whatever object most recently freed it.
The page is then mapped into userspace via vm_insert_page() under
BNXT_RE_MMAP_SH_PAGE in bnxt_re_mmap(). The driver only ever writes
4 bytes (a u32 AVID) at offset BNXT_RE_AVID_OFFT (0x10) inside
bnxt_re_create_ah(); the remaining 4092 bytes of the page are exposed
to userspace unsanitised, leaking kernel memory contents.
Any user with access to /dev/infiniband/uverbsX on a host with a
bnxt_re device (typically rdma group membership) can read this data
via a single mmap() at pgoff 0 after IB_USER_VERBS_CMD_GET_CONTEXT.
Other shared pages in the same file already use get_zeroed_page()
correctly:
drivers/infiniband/hw/bnxt_re/ib_verbs.c
srq->uctx_srq_page = (void *)get_zeroed_page(GFP_KERNEL);
cq->uctx_cq_page = (void *)get_zeroed_page(GFP_KERNEL);
uctx->shpg is the only outlier. Bring it in line with the existing
convention by switching to get_zeroed_page(). |
| The WS Form LITE – Drag & Drop Contact Form Builder plugin for WordPress is vulnerable to PHP Object Injection in all versions up to, and including, 1.10.80 via deserialization of untrusted input from form submission meta values. This makes it possible for unauthenticated attackers to inject a PHP Object. No known POP chain is present in the vulnerable software, which means this vulnerability has no impact unless another plugin or theme containing a POP chain is installed on the site. If a POP chain is present via an additional plugin or theme installed on the target system, it may allow the attacker to perform actions like delete arbitrary files, retrieve sensitive data, or execute code depending on the POP chain present. |
| The Image Photo Gallery Final Tiles Grid plugin for WordPress is vulnerable to Stored Cross-Site Scripting via the 'delay' shortcode attribute in all versions up to, and including, 3.6.12 due to insufficient input sanitization and output escaping. This makes it possible for authenticated attackers, with Contributor-level access and above, to inject arbitrary web scripts in pages that will execute whenever a user accesses an injected page. |
| The Advanced Product Fields (Product Addons) for WooCommerce plugin for WordPress is vulnerable to Improper Input Validation in all versions up to, and including, 1.6.21. This is due to a logic flaw in the 'validate_cart_data' function. This makes it possible for unauthenticated attackers to bypass required paid addons and complete purchases at the base product price only, effectively stealing products by paying a fraction of the intended total. The vulnerability was partially patched in version 1.6.19. |
| The MC4WP: Mailchimp for WordPress plugin for WordPress is vulnerable to Stored Cross-Site Scripting via the form response message post meta fields (e.g., 'text_subscribed', 'text_error') in all versions up to, and including, 4.12.0 due to insufficient input sanitization and output escaping. This makes it possible for authenticated attackers, with Author-level access and above, to inject arbitrary web scripts in pages that will execute whenever a user accesses an injected page. |
| The GreenShift – Animation and Page Builder Blocks plugin for WordPress is vulnerable to unauthorized modification of data in versions up to, and including, 12.8.9. This is due to a missing capability check on the 'gspb_update_global_wp_settings' function that only verifies the 'edit_posts' capability instead of requiring administrative privileges. This makes it possible for authenticated attackers, with contributor-level access and above, to modify global WordPress theme color settings site-wide, leading to site defacement. |
| Joomla Extension - fabrikar.com - Remote code execution in Fabrik < 4.7.2 - An unauthenticated attacker could execute arbitrary code by using the ajax_calc feature of the calc plugin. |
| This CVE ID has been rejected or withdrawn by its CVE Numbering Authority. |
| NLTK versions before 3.9.4 contain a symlink escape vulnerability in CorpusReader.open() that allows local attackers to read arbitrary files outside the corpus root. The vulnerability exists because path validation is lexical and does not account for symlink resolution, enabling attackers to place symlinks inside the corpus root to access files outside the intended boundary. |
| hashcat contains a heap-based buffer overflow (out-of-bounds write) in the outfile_write() function in src/outfile.c. When assembling output into a fixed-size buffer (HCBUFSIZ_LARGE, ~16 MB), the function sequentially appends the username, separator, hash, and plaintext via memcpy without validating that the accumulated length stays within the buffer capacity. When run with --username --show against a crafted hash file containing an oversized username that nearly fills the buffer, the total assembled output exceeds the buffer, causing a heap buffer overflow that can corrupt memory and crash the process. |
| hashcat's fgetl() function in src/filehandling.c writes a null terminator one byte past the caller's buffer when an input line is exactly the buffer length. Attackers can trigger this out-of-bounds heap write by providing a hash file, potfile, or wordlist containing a line of exactly HCBUFSIZ_LARGE bytes. |
